Enhanced Security Measures in Place:   To ensure a safer experience, we’ve implemented additional, temporary security measures for all users.

General Topics
Post a discussion here if you have general questions regarding configuration and troubleshooting for Palo Alto Networks products. Use this forum to collaborate with like-minded security professionals to improve your security posture.
cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Announcements
General Topics
Post a discussion here if you have general questions regarding configuration and troubleshooting for Palo Alto Networks products. Use this forum to collaborate with like-minded security professionals to improve your security posture.
About General Topics
Post a discussion here if you have general questions regarding configuration and troubleshooting for Palo Alto Networks products. Use this forum to collaborate with like-minded security professionals to improve your security posture.

Discussions

Ensuring a Safe and Secure Community: How You Can Help

 

Dear LIVEcommunity Members,

 

Ensuring a top-tier experience on LIVEcommunity and protecting our members’ safety and security is our top priority! To this end, we have implemented additional security measures to safeguard our vibrant global commun

...

safe-community_oct24.jpg
report-content.jpg
jforsythe by Community Team Member
  • 89 Views
  • 0 replies
  • 0 Likes

Threat log types

 

For threat logs in PA  i see below options

 

( subtype neq vulnerability ) and ( subtype neq spyware ) and ( subtype neq packet ) and ( subtype neq scan )

 

need to know if this makes sense ??

 

where vulnerability is part of vul protection scecurity prof

...

MP18 by Cyber Elite
  • 2444 Views
  • 1 replies
  • 0 Likes

Unable to get into maintenance mode

Hello All,

I was in the process of upgrading our firmware of our PA500 to 8.1 and when the device rebooted, it did not want to come back online.  Checked the startup and noticed I was getting this error message.  I did read online that it might be an

...

jsuttor by L0 Member
  • 4048 Views
  • 3 replies
  • 0 Likes

Critical system logs

Hello,

I'am planning to install a monitoring tool, and i need critical system logs generated by the PAN-device. Is there any docs that mention it?

Regards.

asia by L3 Networker
  • 7002 Views
  • 8 replies
  • 0 Likes

Resolved! Connecting WildFire Private Cloud to firewall

When connecting WildFire Private Cloud to firewall (Device > Setup > Wildfire), It appears that we can only add one (1) appliance IP address. However with a cluster there's more than one appliance.

1) Should this be the management IP address of the Pr

...

Resolved! Disabling HA

Hi Community,

 

Does disabling HA using the master switch ( Device -> High availability -> general -> setup ->enable HA checkbox) will cause the interfaces to go down and up ?. I understand that the interface mac has to be changed from virtual to physi

...

Resolved! MineMeld engine failed to start.

I was attmepoting to configure Minemeld to pull AWS ip addresses, but nothing happened when I hit commit. I noticed the Supervisor had stopped, and came across this earlier article. I issued the commands:

sudo service minemeld stop sudo service minem...

Need to allow service for Ping application

Hi Team

 

We have configured the one Destination NAT policy. My requirement is Ping the NAT IP (Public IP) from the external network.

 

I have configured one security policy with application as 'ping' and service as 'any'.

 

For the above configuration, I

...

Resolved! User-ID not mapping all users

I'm using the PA's integrated User-ID Agent to setup User-ID. The moment I began monitoring DC controllers it begain to pull User-ID mappings. This is before User-ID was configured on any zone. However, when I configured User-ID on a source zone, the

...

Resolved! unable to get system info

This is a new one for me. My system is showing "active" (in active/passive) but the GUI is frozen and I see the following on the dashboard:

 

PANOS 8.1.9

 

From the dashboard

fail.png

Migrating server from port based firewall to Pal Alto

My company is moving a few servers from an old data center with an ASA to a new data center with a Pal Alto.  A lot of the rules for the old server on the old firewall are showing port numbers only.  I would like to use application ID as much as poss

...

  • 23584 Posts
  • 107 Subscriptions
Top Liked Authors
Labels