topic Interface goes Down when speed set to 1000! in General Topics

Interface goes Down when speed set to 1000!

Besfort — Tue, 02 Sep 2014 14:15:22 GMT

Hi,

I was getting complains for slow download speed, so I tried to change the speed setting on interface from auto to 1000, but the interface went down.

Link status:

Runtime link speed/duplex/state: unknown/unknown/down

Configured link speed/duplex/state: 1000/auto/up

when I set it back to auto, it goes half duplex and speed 100

Link status:

Runtime link speed/duplex/state: 100/half/up

Configured link speed/duplex/state: auto/auto/up

thanks,

Re: Interface goes Down when speed set to 1000!

ajbool — Tue, 02 Sep 2014 14:22:04 GMT

How is the other side of the link configured?

Re: Interface goes Down when speed set to 1000!

hshah — Tue, 02 Sep 2014 14:24:08 GMT

Bestorf,

There should be issue with other end of interface configuration. It should have been configured in 100/Half.

You should hard code other end with 1000/Full just like this one.

Regards,

Hardik Shah

Re: Interface goes Down when speed set to 1000!

Besfort — Tue, 02 Sep 2014 14:27:56 GMT

the other side in one interface is 100/full duplex and the other 1000/full duplex

Re: Interface goes Down when speed set to 1000!

hshah — Tue, 02 Sep 2014 14:29:36 GMT

Try to configure both in 1000/Full and see behavior.

Any incompatibility can cause in-consistent results.

Regards,

Hardik Shah

Re: Interface goes Down when speed set to 1000!

dmaynard — Tue, 02 Sep 2014 14:34:46 GMT

For more information on 802.3 specifications, refer to the following: IEEE-SA -IEEE Get 802 Program - 802.3: Ethernet

Cannot Commit when Interfaces are Set to 1000/full

Autonegotiation is a requirement for using 1000BASE-T^[11] according to Section 28D.5 Extensions required for Clause40 (1000BASE-T).^[12] At least the clock source has to be negotiated, as one endpoint must be master and the other endpoint must be slave.

Re: Interface goes Down when speed set to 1000!

Besfort — Tue, 02 Sep 2014 14:49:43 GMT

in one side is the Cisco switch with this config:

interface FastEthernet0/2

switchport mode trunk

speed 100

duplex full

spanning-tree portfast trunk

ip dhcp snooping trust

on the other side PAN has this config:

X@PA-500> show interface ethernet1/4

Link status:

Runtime link speed/duplex/state: 100/half/up

Configured link speed/duplex/state: auto/full/up

even though it is configured to full duplex, it goes to half.

Re: Interface goes Down when speed set to 1000!

ajbool — Tue, 02 Sep 2014 14:56:15 GMT

The far end is only a FastEthernet (100) interface - so you won't be able to set the PA to 1000.

Just force the PA to 100 / full duplex and you'll be fine.

Re: Interface goes Down when speed set to 1000!

Besfort — Tue, 02 Sep 2014 15:30:15 GMT

Yes that interface is connected to FastEthernet, but the other one was in GigabyteEthernet.

However the problem with half duplex was because the interface was in VWire and in order to work in fullduplex both VWire interfaces had to be configured for fullduplex. It is strange though that Link Duplex Auto goes to Half by default.

thanks everyone for comments and suggestions.

Re: Interface goes Down when speed set to 1000!

ajbool — Tue, 02 Sep 2014 15:36:05 GMT

Well, you had the Cisco forced to 100/full. This doesn't force the negotiation to 100/full - but instead turns negotiation off altogether. Your PA tried negotiating; couldn't get anything back from the other end and (rather stupidly really) guessed half duplex.