topic Re: DHCP Relay not returning address from MS AD DHCP Server in General Topics

DHCP Relay not returning address from MS AD DHCP Server

Retired Member — Sun, 11 Mar 2012 22:36:28 GMT

We setup a DHCP relay to a MS 2008R2 DHCP server, server recieves the relay and passes a client address back to PA 2050 running 4.1.3, the address does not get passed through to client, logs show only thr DHCP request going out but nothing back, no blocks in logs, we know the address packet is being returned to the server side PALO NIC.

we even opened all protocols both ways, but still nothing going back and no blocks or system errors.

anyone have any ideas?

Thanks

Kind regards

Re: DHCP Relay not returning address from MS AD DHCP Server

Kevin.lane — Mon, 12 Mar 2012 23:03:47 GMT

Hi,

We ran into this problem as well when we were running Active-Active HA. When one is Suspended, it works fine. Do you by any chance run your setup that way?

Regards,

Kevin

Re: DHCP Relay not returning address from MS AD DHCP Server

Retired Member — Tue, 13 Mar 2012 08:07:18 GMT

Hi,

No, we only run single 2050.

Kind regards

Re: DHCP Relay not returning address from MS AD DHCP Server

tysver — Thu, 10 May 2012 07:38:38 GMT

We have one PA2050, with PANOS v3.1.9 with 2 virtual routers. A inner and outer router.

The outer router routes traffic to our external sites.

We also have problems with dhcp-replies from our MS 2008 R2 DHCP server.

I can se the dhcp-requests in the dhcp log on the dhcp-server.

I see the dhcp-requests from the external routers in PA monitor and i see the replies back to the routers in the monitor.

The dhcp server updates the leasetime for the scopes and all looks fine.

But, the clients does not receive the dhcp replies.

I rebooted the PA 2 days ago because of several subnets without dhcp-replies coming through.

Yesterday all looked good.

Today i have 2 other subnets with dhcp problems.

I also lost dhcp to several subnets when i commited some small changes 2 days ago.

I cant see any logic in ths strange behaviour.

It's always subnets connected to the outer PA virtual router (external sites) that experiencs these problems.

The outer router has about 110 routes.

Wh have just changed our external IP-plan and therefore we have a lot of routes to all the externel subnets while we have changed network by network.

I'm going to delete at least 70 of the routes and replace them with 7 routes with a bigger mask.

I'm a bit stuck right now....

Regards,

Geir

Norway

Re: DHCP Relay not returning address from MS AD DHCP Server

Kevin.lane — Fri, 11 May 2012 02:18:26 GMT

I'm not sure if this is helpful or not, but one of our other DHCP issues we run into is due to the route to the DHCP server being dropped.

Example:

On the PA, we have zone X which provides services to a particular set of clients. We then have zone Y which connects the main part of our network, including the DHCP server. Zone X router does a DHCP relay to the DHCP server through the PA. This works fine normally. However, sometimes, the switch between the PA and the router controlling our main network reboots. When that happens, our DHCP from zone X begins failing.

Going into session browser on the PA shows that because the route to the DHCP server was lost when the PA dropped its OSPF connection to the main network router, the DHCP requests started being sent to the "Outside" zone and essentially the session just locks. When I delete that session, it starts going back the proper way and DHCP begins working again.

It may be completely unrelated, but the session browser might be a good place to see anything odd happening.

Regards

Kevin

Re: DHCP Relay not returning address from MS AD DHCP Server

Retired Member — Fri, 11 May 2012 07:02:14 GMT

Hi,

In our setup we run static routes, so that won't be an issue for us.

We are going to test again when we move to 4.6 soon, to see if that resolves

Regards