topic Re: How to setup multiple IP Public address on PA-200 in General Topics

How to setup multiple IP Public address on PA-200

mbeghdadi — Fri, 13 Feb 2015 20:52:43 GMT

Hi,

We're facing an architecture where there are multiple address that needs to be used for a specific pool of IP from the LAN interface.

Let's supose that we have 3 IP PUBLIC address 10.X.X.2; 10.X.X.3 and 10.X.X.4 and the gateway has the IP 10.X.X.1

From the LAN interface we might expect to get a range of IP Pool addresses

192.168.1.X to 192.168.1.Y

192.168.1.Z to 192.168.1.W

192.168.1.T to 192.168.1.U

Traffic from the LAN to the WAN should expect the rule as stated below:

LAN from 192.168.1.X to 192.168.1.Y to WAN 10.X.X.1

192.168.1.Z to 192.168.1.W to WAN 10.X.X.2

192.168.1.T to 192.168.1.U to WAN 10.X.X.3

First question, Can we define a PORT INTERFACE with multiple IP public interface? If so,

Second Question, Shall we create a NAT rule for each range of IP pool?

Do we need to create several static route within the VIRTUAL ROUTERS as we have several IP addresses.

Your thoughts are much appreciated...

Re: How to setup multiple IP Public address on PA-200

bat — Fri, 13 Feb 2015 21:19:16 GMT

mbeghdadi

There is no need to define all the IPs on the public Interface, if they are all of the same network then just create NAT rules using and device will automatically respond to ARP for these IPs

You will have to create NAT rule if you want to 1-1 mapping between the LAN networks and public IPs

I don't think there is any need of virtual routers on LAN side as long as all the networks are different.

Hope it helps!

Re: How to setup multiple IP Public address on PA-200

pulukas — Fri, 13 Feb 2015 22:01:38 GMT

Welcome to PanOS. It sounds like what you want is one-to-one nat for the three servers.

Have a look at this document for PanOS nat. Page 15 and following is the the one-to-one nat configuration process you will follow.

Understanding PAN-OS NAT

Re: How to setup multiple IP Public address on PA-200

HULK — Fri, 13 Feb 2015 22:11:27 GMT

Hello,

bat is correct.

You may follow this discussion from prxy ARP feature: Re: Proxy-Arp behavior and NAT's

ARP Proxy

Thanks

Re: How to setup multiple IP Public address on PA-200

mbeghdadi — Fri, 13 Feb 2015 22:26:17 GMT

Hi All,

Thanks for your quick feedback.

so If I understood your points.

Looks like I just ned to define an IP address for the WAN port interface? But which one ? 10.X.X.2; 10.X.X.3 and 10.X.X.4 ?

Then I have to configure a One to One NAT rule ? But How? Like the one below

NAT RULE

source LAN

Zone TRUST

Source address 192.168.1.X to 192.168.1.Y (X could be 10 and Y 50)

Destination WAN

Zone UNTRUST

Destination address 10.X.X.2

The idea is to have One FIREWALL, One ISP, but within the LAN, there are several companies and therefore each companies will get and be assigned with a range of IP LAN addresses and each company will get its own IP public address using a common WAN interface

Re: How to setup multiple IP Public address on PA-200

HULK — Fri, 13 Feb 2015 22:42:58 GMT

Hello,

You can configure one IP address on the interface i.e 10.X.X.1

Configure the NAT rule as mentioned below.

NAT RULE-1

Zone TRUST

Source address 192.168.1.X to 192.168.1.Y (X could be 10 and Y 50)

Destination ANY

Zone UNTRUST

Destination address ANY

Source NAT:

Translation type: Dynamic IP and port

Address type: translated address

Address:10.X.X.1

=================================

NAT RULE-2

Zone TRUST

Source address 192.168.1.A to 192.168.1.B (A could be 64 and B 128)

Destination ANY

Zone UNTRUST

Destination address ANY

Source NAT:

Translation type: Dynamic IP and port

Address type: translated address

Address:10.X.X.2

=================================

NAT RULE-3

Zone TRUST

Source address 192.168.1.M to 192.168.1.N (M could be 129 and N 255)

Destination ANY

Zone UNTRUST

Destination address ANY

Source NAT:

Translation type: Dynamic IP and port

Address type: translated address

Address:10.X.X.3

Thanks

Re: How to setup multiple IP Public address on PA-200

HULK — Fri, 13 Feb 2015 22:45:50 GMT

As per the above mentioned NAT policy,

Company A (192.168.1.1 to 192.168.1.63) will translate ( source NAT) to public IP 10.X.X.1

Company B (192.168.1.64 to 192.168.1.127) will translate ( source NAT) to public IP 10.X.X.2

Company C (192.168.1.128 to 192.168.1.255) will translate ( source NAT) to public IP 10.X.X.3

Thanks

Re: How to setup multiple IP Public address on PA-200

mbeghdadi — Fri, 13 Feb 2015 23:13:30 GMT

Hello,

I do appreciate your support and quick recommendations. I'll try to configure in the way you mentionned and get back to you guys..

Again thanks a lot !!