topic Re: how to distribute one internet line to multiple services in General Topics

how to distribute one internet line to multiple services

MFayez — Sun, 07 Apr 2019 12:08:30 GMT

in my current scenario, I have 4 interfaces configured with different Public IP address and each interface linked to the different router and each interface have different services (Internet Email1, Email2, VPN)

Our Plan to get a new line from a new ISP, in these case, we got only one router and the old Routers we canceled and we will get 6 Public IP address My Question :

1- How I configure the 4 interfaces to one router
2- required configure subinterface
3- what is the requirement for complete this project

Re: how to distribute one internet line to multiple services

MFayez — Sun, 07 Apr 2019 12:11:20 GMT

Re: how to distribute one internet line to multiple services

jeremy.larsen — Mon, 08 Apr 2019 13:55:56 GMT

Why are you using separate ports for each service? This seems to be an extreme waste of ports. Why not just use a single port on the PAN and create subinterfaces for each service if you are going to separate them that way?

ISP <---> Router <---> PAN (subinterface 1,2,3,4)

Re: how to distribute one internet line to multiple services

Mick_Ball — Mon, 08 Apr 2019 13:57:48 GMT

I have 6 ISP's with up to 62 ip's each.

I have used subinterfaces.

you add first IP to layer 3 port and in advanced, tick "untagged subinterface"

select the interface and at the bottom of the page you can add subinterface.

give it a unique number (I use the last octet of the address as a reference) and add it to it's own zone.

not everyones cup of tea but works for me...

Re: how to distribute one internet line to multiple services

MFayez — Mon, 08 Apr 2019 14:00:30 GMT

How i create subinterfaces and how i can linked to zones

Re: how to distribute one internet line to multiple services

Mick_Ball — Mon, 08 Apr 2019 14:06:50 GMT

add one ip address to interface 1/1 and go to advanced and tick the box for "untagged subinterface"

then select the interface again and the option to add a subinterface is at the bottom of the page

Re: how to distribute one internet line to multiple services

jeremy.larsen — Mon, 08 Apr 2019 14:08:13 GMT

I think you should read through the PAN Administrators Guide. This is all covered in the standard documentation.

Re: how to distribute one internet line to multiple services

Mick_Ball — Mon, 08 Apr 2019 14:45:26 GMT

slightly different but same result as no tagging involved

i had to reduce in size as i could not draw the red pointy multi pronged thing...

Re: how to distribute one internet line to multiple services

jeremy.larsen — Mon, 08 Apr 2019 15:53:19 GMT

That works too if you don't care about your subinterface broadcast traffic overlapping.

Re: how to distribute one internet line to multiple services

MFayez — Tue, 09 Apr 2019 06:19:37 GMT

after I create the subinterface, must be linked to virtual Router IP

Re: how to distribute one internet line to multiple services

jeremy.larsen — Tue, 09 Apr 2019 13:29:09 GMT

Is that a question?

Re: how to distribute one internet line to multiple services

MFayez — Tue, 18 Jun 2019 08:08:53 GMT

this case still is not clear for me i will explain current setup

1- 4 router is connected phiscaly to PA and each router provide defrent services (Email , Internet , VPN)

2- PBF are configer for pass the traffice and NAT

3-One defult routur are configer for untrust zone for all services

Our reqiuerment :

1- Shift to 4 router to 1 Fiber line

@Mick_Ball @jeremy.larsen