topic Re: CLI command for transceiver light levels in General Topics

CLI command for transceiver light levels

mikeatt — Tue, 03 Apr 2018 21:56:27 GMT

What is the CLI command for viewing transceiver light levels? Palo Alto 7050

Re: CLI command for transceiver light levels

BPry — Wed, 04 Apr 2018 12:07:40 GMT

I'm not actually sure that this gives you the light levels, but the most detailed command that I've been able to find for individual interfaces is 'show system state filter-pretty sys.sx.py.stats' where X is the slot number and Y is the port number.

Re: CLI command for transceiver light levels

mikeatt — Wed, 04 Apr 2018 19:53:32 GMT

Thanks for the reply. I have asked for someone to test the command you provided, but not sure how long it will take them. Will post when I know.

Re: CLI command for transceiver light levels

mikeatt — Thu, 12 Apr 2018 19:02:08 GMT

Still waiting on test of command

Re: CLI command for transceiver light levels

mikeatt — Thu, 12 Apr 2018 20:14:18 GMT

I was told by PA support that they do not have the feature and no plans to get it. So that means a physical dispatch is required to simply check light levels. Not good.

Re: CLI command for transceiver light levels

BPry — Thu, 12 Apr 2018 20:23:01 GMT

@mikeatt,

I would check with your SE if there is an active feature request to add this feature into PAN-OS. If there is post it here so that others can add their votes to it 😉

Re: CLI command for transceiver light levels

savariya — Wed, 11 Sep 2019 14:41:16 GMT

Hi All,

We are also having the same situation, however I have raised a ticket with PA support desk. Will update you if I get some positive feedback.

Regards

Binoj Savariyar

Re: CLI command for transceiver light levels

MP18 — Sat, 28 Sep 2019 04:52:49 GMT

It is good to have that feature as we will be using HSCI port on PA5220.

Hope PA will add this feature soon

Re: CLI command for transceiver light levels

tshooter — Thu, 20 May 2021 18:42:23 GMT

How is this not added yet??

Oh Hey Palo Alto Networks I have some amazing info that could bring huge simple improvements with security rule management. please reach out to me.

Re: CLI command for transceiver light levels

MP18 — Fri, 21 May 2021 05:09:48 GMT

@tshooter

On version PAN OS 10.00 they have feature for transceiver light levels.

how transceiver-detail ethernet1/11

--------------------------------------------------------------------------------

Detailed Transceiver Information

--------------------------------------------------------------------------------

Interface: ethernet1/11

Vendor Name: AVAGO

Vendor Part Number: AFBR-5715PZ Rev

Vendor Serial Number: AM17332V6LD

Link Length for 62.5/125 um OM1 fiber: 270 m

Link Length for 50/125 um OM2 fiber: 550 m

Link Length for 50/125 um OM3 fiber: 0 m

Link Length for 50/125 um OM4 fiber: 0 m

Diagnostic Monitor Information:

--------------------------------------------------------------------------------

Alarms Warnings

High Low High Low

--------------------------------------------------------------------------------

Temperature 0.00 C 3.02 C 7.00 C 0.00 C 1.12 C

Voltage 0.00 V 1.64 V 0.00 V 0.31 V 0.00 V

Current 0.00 mA 28.21 mA 0.00 mA 33.45 mA 33.42 mA

TX Power 0.00 mW 2.03 mW 0.82 mW 0.82 mW 0.82 mW

RX Power 0.00 mW 0.82 mW 0.82 mW 0.00 mW 0.60 mW

--------------------------------------------------------------------------------

Regards

Re: CLI command for transceiver light levels

mduhon — Fri, 06 Jan 2023 01:02:58 GMT

my Palo 5220 on PanOS 10.2.2 says that's not a command. What am I missing?

Re: CLI command for transceiver light levels

BPry — Fri, 06 Jan 2023 01:36:55 GMT

@mduhon,

Just to verify, you are trying 'show' instead of the indicated 'how' correct? The command definitely exists on PAN-OS 10.2 and PAN-OS 11.0 without change.

Re: CLI command for transceiver light levels

mduhon — Fri, 06 Jan 2023 18:12:25 GMT

Yes I was doing the show command not the how. But there was another mistake I was doing, I used a saved putty connection and noticed this morning I was connecting to our old palo that is no longer in use and only on OS 9 not 10. Changed to the actual production palo and I was able to use that command. This was my fault for not noticing that. Thanks for the quick reply.

Re: CLI command for transceiver light levels

mpugina — Mon, 28 Aug 2023 21:54:12 GMT

Yes but doesn't show light levels