not-resolved URL Category

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Announcements
Palo Alto Networks Approved
Palo Alto Networks Approved
Community Expert Verified
Community Expert Verified

not-resolved URL Category

L4 Transporter

We are seeing a large amount of url logs being categorized as 'not-resolved' at a rate of about 5500 per hour. After reviewing logs to compare it appears it started a few days previous. What is strange is a site will be categorized as 'not-resolved' but a second or two later it is properly categorized.

For example: www.napaautopro.com category = not -resolved then 2 seconds later www.napaautopro.com category = motor-vehicles

Seems as if we are not being able to check into the PAN-DB and it is timing out. Also when trying to reclassify a site through the firewall we get timeouts. I suspect these symptoms are related.

I have submitted a ticket to support but wanted to see if any other users have experienced this too. We are currently on OS 5.0.10 and our PAN-DB URL subscription is active.

1 accepted solution

Accepted Solutions

Since I have run the restart management command the 'not-resolved' issue no longer exist. Investigating with support now if it is a memory leak. Thanks for everyones input.

View solution in original post

13 REPLIES 13

L5 Sessionator

Hi Lewis,

Issue might be with high management-server and device server. Can you run "show system resources | match srvr" and paste it to the case.

You can try restarting both process. It will not impact your production traffic, will restart the services which handles URL related processes.

debug software restart management-server

debug software restart device-server

Hope this helps. Thank you.

L4 Transporter

Hello Lewis,

The category of a URL is determined in the following top-down approach:

1. Block list

2. Allow list

3. Custom Categories

4. DP URL cache

5. MP URL database(Base DB)

6. MP dyanamic database(Dynamic DB)

7. Cloud server(Cloud DB)---if dynamic url-filtering is enabled in the URL filtering profile.

URLs will show up as no-resolved if there is no response from MP in 5sec(default timeout can be changed) or if MP is unable to connect to the cloud(when it doesn't have that URL in its database).

Make sure the management-server is not too busy. You can restart management-server(typically during off peak hours) and device-server. If its because of MP or device-server, the issue should be fixed here.

>debug software restart management-server

>debug software restart device-server

Also check if the firewall is able to connect to cloud

>show url-cloud status

Hope it helps!

-Dileep

L6 Presenter

Hi Lewis,

For any URL category following sequence of event happens.

1. DP looks for category in DP cache.

2. If it doesnt find than it contacts MP

3. If MP doesnt respond in 5 second than its classified as "Not-Resolved"

Please provide followinng output.

1.  show counter global filter delta yes | match url

2. After 30 Second Execute same command again " show counter global filter delta yes | match url"

3. After 30 Second Execute same command again " show counter global filter delta yes | match url"

Provide me output for 2 and 3.

Regards,

Hardik Shah

lewiscc@PAN1-5020(active)> show counter global filter delta yes | match url

flow_url_category_msg_recv              3406        6 info      flow      pktproc   Flow msg: url category messages received

ctd_handle_reset_and_url_exit            217        0 info      ctd       pktproc   Handle reset and url exit

ctd_url_block                          12900       26 info      ctd       pktproc   sessions blocked by url filtering

ctd_url_block_cont                      2031        3 info      ctd       pktproc   sessions prompted with block/cont for url filtering

log_url_cnt                           487575     1009 info      log       system    Number of url logs

log_url_req_cnt                        10217       20 info      log       system    Number of url request logs

proxy_url_request_timeout                127        0 warn      proxy     pktproc   The url category request for ssl proxy is timedout

proxy_url_request_pkt_drop               610        1 drop      proxy     pktproc   The number of packets get dropped because of waiting for url category request in ssl proxy

proxy_url_category_unknown                62        0 info      proxy     pktproc   Number of sessions checked by proxy with unknown url category

url_db_request                         10217       20 info      url       pktproc   Number of URL database request

url_db_reply                           15010       30 info      url       pktproc   Number of URL reply

url_flow_state_invalid                   887        1 info      url       session   The session's state was changed when receiving url response

url_flow_unmatched                        74        0 warn      url       pktproc   The url response does match flow key

url_request_timeout                     2059        4 info      url       pktproc   The url category request is timedout

url_request_pkt_drop                   23631       48 drop      url       pktproc   The number of packets get dropped because of waiting for url category request

url_session_not_in_wait                 1585        2 error     url       system    The session is not waiting for url

url_session_not_in_ssl_wait              130        0 error     url       system    The session is not waiting for url in ssl proxy

url_reply_not_distribute                   4        0 warn      url       pktproc   Number of URL reply not distributed to other DPs

lewiscc@PAN1-5020(active)> show counter global filter delta yes | match url

flow_url_category_msg_recv               739       20 info      flow      pktproc   Flow msg: url category messages received

ctd_handle_reset_and_url_exit             53        0 info      ctd       pktproc   Handle reset and url exit

ctd_url_block                            999       27 info      ctd       pktproc   sessions blocked by url filtering

ctd_url_block_cont                       190        4 info      ctd       pktproc   sessions prompted with block/cont for url filtering

log_url_cnt                            36049     1018 info      log       system    Number of url logs

log_url_req_cnt                          869       24 info      log       system    Number of url request logs

proxy_url_request_timeout                  5        0 warn      proxy     pktproc   The url category request for ssl proxy is timedout

proxy_url_request_pkt_drop                30        0 drop      proxy     pktproc   The number of packets get dropped because of waiting for url category request in ssl proxy

proxy_url_category_unknown                 6        0 info      proxy     pktproc   Number of sessions checked by proxy with unknown url category

url_db_request                           869       24 info      url       pktproc   Number of URL database request

url_db_reply                            3076       86 info      url       pktproc   Number of URL reply

url_flow_state_invalid                   160        4 info      url       session   The session's state was changed when receiving url response

url_flow_unmatched                         6        0 warn      url       pktproc   The url response does match flow key

url_request_timeout                      167        4 info      url       pktproc   The url category request is timedout

url_request_pkt_drop                    2295       64 drop      url       pktproc   The number of packets get dropped because of waiting for url category request

url_session_not_in_wait                  399       11 error     url       system    The session is not waiting for url

url_session_not_in_ssl_wait               18        0 error     url       system    The session is not waiting for url in ssl proxy

lewiscc@PAN1-5020(active)> show counter global filter delta yes | match url

flow_url_category_msg_recv                42        0 info      flow      pktproc   Flow msg: url category messages received

ctd_handle_reset_and_url_exit             27        0 info      ctd       pktproc   Handle reset and url exit

ctd_url_block                            892       30 info      ctd       pktproc   sessions blocked by url filtering

ctd_url_block_cont                        99        2 info      ctd       pktproc   sessions prompted with block/cont for url filtering

log_url_cnt                            29500     1044 info      log       system    Number of url logs

log_url_req_cnt                          616       21 info      log       system    Number of url request logs

proxy_url_request_timeout                 21        0 warn      proxy     pktproc   The url category request for ssl proxy is timedout

proxy_url_request_pkt_drop                81        2 drop      proxy     pktproc   The number of packets get dropped because of waiting for url category request in ssl proxy

proxy_url_category_unknown                 3        0 info      proxy     pktproc   Number of sessions checked by proxy with unknown url category

url_db_request                           616       21 info      url       pktproc   Number of URL database request

url_db_reply                             244        8 info      url       pktproc   Number of URL reply

url_request_timeout                       65        2 info      url       pktproc   The url category request is timedout

url_request_pkt_drop                     721       24 drop      url       pktproc   The number of packets get dropped because of waiting for url category request

url_session_not_in_wait                   22        0 error     url       system    The session is not waiting for url

url_session_not_in_ssl_wait                7        0 error     url       system    The session is not waiting for url in ssl proxy

Hi Lewis,

I can see following counter in each iteration of output.

url_request_pkt_drop                    2295       64 drop      url       pktproc   The number of packets get dropped because of waiting for url category request

It means "number of packets dropped while waiting for response from mp."

Please provide us output for " show system resources | match srvr"

Regards,

Hardik Shah

output from show system resources | match srv

2177 20 0 681m 466m 11m S 97 11.8 6212:03 devsrvr

2151 20 0 1128m 815m 7060 S 63 20.6 19252:08 mgmtsrvr


going to restart the mgmt server (debug software restart management-server)

Hi Lewis,

That is the right idea. Right now management server is running above 1 Gb.

2151 20 0 1128m 815m 7060 S 63 20.6 19252:08 mgmtsrvr >>>>>>>>>>>>>>1128m =1.2 Gb

Please restart it with command "debug software restart management-server"

Regards,

Hardik Shah

Since I have run the restart management command the 'not-resolved' issue no longer exist. Investigating with support now if it is a memory leak. Thanks for everyones input.

Hi Lewis,

Right now PANW is on 5.0.10 which is much older release. Latest release is 5.0.14 and soon they will release 5.0.15.

Even if they find any potential bug in 5.0.10, the recommendation would be to upgrade to latest release.

Right now recommended release is 5.0.13.

Let me know if you have any other thoughts.

Regards,

Hardik Shah.

We are scheduled to go to 6.0.5 in the next couple weeks. So hopefully this issue will no longer exist. thanks for your input.

Hi Lewis,

5.0.9 had similar issue reported, which was closed due to inactivity. Hence there is no bug in 5.0.10. which matches exact symptoms.

I would suggest to upgrade to 5.0.13. Please find the release note for the same.

https://downloads.paloaltonetworks.com/software/PAN-OS-5.0.13-RN.pdf?__gda__=1413868782_ba2d6a38eed9...

Regards,

Hardik Shah

Hi Lewis,

6.0.5 is also one of the recommended release, I suggested 5.0.13 because its on the same trail as 5.0.6.

Let me know if it helps and feel free to ask any future queries.

Regards,

Hardik Shah

L6 Presenter

we resolved the same issue using command

debug software restart device-server

  • 1 accepted solution
  • 10153 Views
  • 13 replies
  • 1 Likes
Like what you see?

Show your appreciation!

Click Like if a post is helpful to you or if you just want to show your support.

Click Accept as Solution to acknowledge that the answer to your question has been provided.

The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!

These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the LIVEcommunity as a whole!

The LIVEcommunity thanks you for your participation!