Reloading Config: Internal Server Error

Announcements

ATTENTION Customers, All Partners and Employees: The Customer Support Portal (CSP) will be undergoing maintenance and unavailable on Saturday, November 7, 2020, from 11 am to 11 pm PST. Please read our blog for more information.

Reply
Highlighted
Cyber Elite

Reloading Config: Internal Server Error

So I just installed minemeld this morning so bare with me as I don't really have everything down yet. The issue that I currently ran into is that when I go under the Config tab I immediately receive an "Error Reloading Config: Internal Server Error" and it says that there is No data available in the table. I'm trying to add our own blocklist as a node, however when I go to add it (Give it a name, select the Prototype that I setup for the blacklist we already had, leave INPUTS empty and Output enabled) the OK button never actually works and always stays grayed out.  Is there a log file or something that will give me some information on what is going on? 


Accepted Solutions
Highlighted
L3 Networker

OK when you run this:

 

sudo -u minemeld /opt/minemeld/engine/current/bin/supervisorctl -c /opt/minemeld/local/supervisor/config/supervisord.conf stop all

 

sudo -u minemeld /opt/minemeld/engine/current/bin/supervisorctl -c /opt/minemeld/local/supervisor/config/supervisord.conf start all

 

Does everything fire up correctly after that?

View solution in original post


All Replies
Highlighted
L7 Applicator

I think the engine is not running.

 

Could you give the following command and attach the output ?

 

sudo service minemeld stop
sudo service minemeld start
sudo -u minemeld /opt/minemeld/engine/current/bin/supervisorctl -c /opt/minemeld/local/supervisor/config/supervisord.conf status
Highlighted
Cyber Elite

minemeld-engine RUNNING pid 56625, uptime 0:01:01
minemeld-traced RUNNING pid 56626, uptime 0:01:01
minemeld-web RUNNING pid 56627, uptime 0:01:01

I just checked and the problem still persists. 

L7 Applicator

Could you check /opt/minemeld/log/minemeld-web.log contents and look for an ERROR string ?

 

Thanks.

Highlighted
Cyber Elite

I don't see anything in the output that says ERROR. I've attached a screenshot of the actual error. 

Highlighted
L3 Networker

Run this:

sudo -u minemeld /opt/minemeld/engine/current/bin/supervisorctl -c /opt/minemeld/local/supervisor/config/supervisord.conf status | awk '{print $4}' | awk -F \, '{print $1}'

 

Get the pids then see if they are all running:

 

ps aux | grep PIDNUMBERFROMCOMMAND1 | grep -v grep

 

 

Highlighted
Cyber Elite

They all appear to be running

56625
56626
56627

\bprya@vpro-panmm-01:~$ ps aux | grep 56625 | grep -v grep
minemeld  56625  0.0  1.0 216048 22212 ?        Sl   12:13   0:04 /opt/minemeld/engine/0.9.22/bin/python /opt/minemeld/engine/current/bin/mm-run /opt/minemeld/local/config
\bprya@vpro-panmm-01:~$ ps aux | grep 56626 | grep -v grep
minemeld  56626  0.0  1.3 232640 27304 ?        Sl   12:13   0:00 /opt/minemeld/engine/0.9.22/bin/python /opt/minemeld/engine/current/bin/mm-traced /opt/minemeld/local/config/traced.yml
\bprya@vpro-panmm-01:~$ ps aux | grep 56627 | grep -v grep
minemeld  56627  0.0  0.9  55980 19904 ?        S    12:13   0:02 /opt/minemeld/engine/0.9.22/bin/python /opt/minemeld/engine/current/bin/gunicorn -w 1 -b 127.0.0.1:5000 --access-logfile - --error-logfile - -k gevent minemeld.flask:app
Highlighted
L3 Networker

OK when you run this:

 

sudo -u minemeld /opt/minemeld/engine/current/bin/supervisorctl -c /opt/minemeld/local/supervisor/config/supervisord.conf stop all

 

sudo -u minemeld /opt/minemeld/engine/current/bin/supervisorctl -c /opt/minemeld/local/supervisor/config/supervisord.conf start all

 

Does everything fire up correctly after that?

View solution in original post

Highlighted
Cyber Elite

All three started correctly and is still giving the same error. 

Highlighted
Cyber Elite

Sorry, I knew I should have had my normal amount of coffee today. There's this nice little load button that I wasn't pressing; once I pushed that I was able to make the changes that I needed to.

Is it friday yet :)

Like what you see?

Show your appreciation!

Click Like if a post is helpful to you or if you just want to show your support.

Click Accept as Solution to acknowledge that the answer to your question has been provided.

The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!

These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the Live Community as a whole!

The Live Community thanks you for your participation!