About bit_byte

network flow  Lan Network -->Firewall A----->switch -->-Firewall B ---->Internet-------->Database server  We are facing issue to connect database server from our lan network. We took packet capture on Firewall A and firewall B . When we initiate traffic from LAN network to database server: Firewall B ; We are getting client Hello and server hello message on Firewall B Firewall A: Only client hello message we got means server hello message drop by firewall A  that why we could not able to connect with database server. We are not using any decryption and proxy we have checked counter value also we did not get any drop. traffic monitor logs session end reason: TCP-rst by client @ MP18 @ Vsys_remo @ Reaper             ... View more

two PA firewalls and we configured in HA (Active-Passive mode). We got /28 subnet from ISP for 2 internet lease line links. (Single ISP) configured links on one firewall with IP 99.100.100.111 on interfacet 4 and 94.100.100.110 on interface 2. With next hope 94.100.100.109 after commit we got interface overlap error. Is it possible to configure this ? @BPry @MP18 ... View more

passive firewall Active firewall. =============================================== we did failover from secondary firewall to primary. After failover Primary firewall all vpn tunnels came up and On passive firewall tunnel info up. is it normal behavior on passive firewall tunnel info up ? or passive firewall tunnle info and IKe info should down ? active firewall below image .. passive firewall below image we can able to see IKE info is down but tunnel info is up . passive firewall I think both IKE and tunnel should be down.   is that normal on the passive firewall tunnel info up? or  GUI error?     ... View more

Behind the firewall, we have 3 servers which access by the remote user. We want to prioritize servers service so the remote user(connected with Global protect)  access this server on optimize way @Reaper    ... View more

LACP configure between PA and cisco switch  Active and Active mode and transmission rate: slow ====================================== LACP System log::::LACP interface ethernet1/19 moved out of AE-group ae2. Selection state Unselected(Link down)   l2ctrld.log file below  2020-04-12 00:19:25.085 +0400 Got port 82 event, link 0, speed 4, duplex 2 2020-04-12 00:19:25.086 +0400 port 82 is full duplex. Enable lacp 2020-04-12 00:19:25.086 +0400 ethernet1/19 idx 82 mux state change RX_TX=>ATTACHED, select_state Unselected(Link down), partner state 0x3d 2020-04-12 00:19:25.086 +0400 post LACP event to DP: if_idx 82, up 0 2020-04-12 00:19:25.086 +0400 log ethernet1/19 idx 82 leaves lag. sel state Unselected(Link down) 2020-04-12 00:19:25.335 +0400 ethernet1/19 idx 82, mux state change ATTACHED=>DETACHED 2020-04-12 00:20:36.584 +0400 ethernet1/19 idx 82, current_while expired. 2020-04-12 00:20:36.584 +0400 ethernet1/19 idx 82, rx state change CURRENT=>EXPIRED 2020-04-12 00:20:39.584 +0400 ethernet1/19 idx 82, current_while expired. 2020-04-12 00:20:39.584 +0400 ethernet1/19 idx 82, rx state change EXPIRED=>DEFAULTED 2020-04-12 00:23:09.585 +0400 Got port 82 event, link 1, speed 4, duplex 2 2020-04-12 00:23:09.585 +0400 port 82 is full duplex. Enable lacp   what could be the reason for Flapping and how we can resolve ... View more

We can configure an email server profile with domain name/server IP. there we can not provide username and password for SMTP Authentication. We wouldn’t see any Username and Password in Email server Profile. Is it possible to configure Username and Password in Email server Profile?    ... View more