This website uses cookies essential to its operation, for analytics, and for personalized content. By continuing to browse this site, you acknowledge the use of cookies.
For details on cookie usage on our site, read our Privacy Policy
For details on cookie usage on our site, read our Privacy Policy
About rperkin
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
- LIVEcommunity
- About rperkin
08-18-2015
7Posts
0Likes
0Solutions
Aug 18, 2015Last Visited
User
Activity
User
Profile
Latest posts by rperkin
| Subject | Views | Posted |
|---|---|---|
| 1134 | 10-03-2013 03:23 AM | |
| 1571 | 09-26-2013 08:08 AM | |
| 1663 | 09-26-2013 02:11 AM | |
| 5493 | 09-19-2013 05:00 AM | |
| 5601 | 09-19-2013 04:19 AM |
User Badges
Community Statistics
| Member Since | 09-19-2013 01:27 AM |
| Date Last Visited | 08-18-2015 09:07 AM |
| Posts | 7 |
10-03-2013
03:23 AM
I am trying to configure 2 x 5020's in an Active/Active Configuration and the run 2 Virtual Systems I am facing issues when enabling the Virtual Systems and the configs stop replicating and then I get backplane failures and have to remove the VSYS config and reboot I cannot find any solid documentation or designs and am now putting this out to the community to see if I am trying to do anything crazy or if this should be quite a straightforward design. Thanks Roger
... View more
09-26-2013
08:08 AM
This is now working now as I think I just had commited too many changes on different boxes. However one annoying behaviour is if I put a description on int E1/1 on PA1 then sync the configs it overwrites the description on PA2 e1/1 How do I stop this happening as each interface goes to a different port on the downstream switch
... View more
09-26-2013
02:11 AM
I am setting up a pair of 5020's in an Active / Active configuration. I am getting confused over the config sync feature and have been overwriting configs on each box. i.e I configured some aggregate interfaces on Box 1 and then I synced the config on Box 2 which overwrote the config and wiped them out. I am also in a situation now where the GUI says Running Config not syncronised and if I try to sync it fails, however if I initiate a manual sync it works? PA-5020-1(active-primary)> request high-availability sync-to-remote running-config Successfully synchronized running configuration with HA peer admin@PA-5020-1(active-primary)> Is anyone running an Active / Active setup. I just need some basic info on what the best way to drive these boxes is? Thanks Roger
... View more
09-19-2013
05:00 AM
It is working! The 1 on the Cisco output refers the the Native Vlan The port is running as a trunk and any traffic that comes into the trunk that is not tagged will be put into Vlan 1 Roger
... View more
09-19-2013
04:19 AM
OK I have managed to get it working now L3 interface which is trunking to a Cisco 3750 and L3 subinterfaces which I can ping from the Cisco Cisco 3750 Configuration interface FastEthernet1/0/1 switchport trunk encapsulation dot1q switchport mode trunk end SwitchTEST#sh int trunk Port Mode Encapsulation Status Native vlan Fa1/0/1 on 802.1q trunking 1 Thanks for the help Is there any documentation about how the Palo's form a trunk? I just set the Cisco to mode trunk and it works so assume that is the best thing to do? Roger Currently studying for my CCIE in R&S! latest updates on my CCIE Blog - www.rogerperkin.co.uk/ccie
... View more
Contact Me
| Online Status |
Offline
|
| Date Last Visited |
08-18-2015
09:07 AM
|
Latest Tags
No tags yet
LEGAL NOTICES
Copyright 2007 - 2023 - Palo Alto Networks