About hyadavalli

hyadavalli · ‎05-26-2015

Hello Robert, I'd recommend opening case with support with tech support file attached. Regards, Hari Yadavalli

hyadavalli · ‎05-26-2015

Hello Satish, My best bet would be is there a space left in the filter(something) just below the Available groups? Regards, Hari Yadavalli

hyadavalli · ‎05-26-2015

Hello Satish, Can you share a screenshot of that error please? Regards, Hari Yadavalli

hyadavalli · ‎05-26-2015

Hello, Create security policy with with your custom categories in the service column instead of applying as security profile. Regards, Hari Yadavalli

hyadavalli · ‎03-20-2015

Hello Mike, This issue is addressed now. Regards, Hari Yadavalli

hyadavalli · ‎03-20-2015

Hello Mike, We are working on a fix for this issue which is ongoing. Can you open a case with support with tech support file attached? Regards, Hari Yadavalli

hyadavalli · ‎03-20-2015

Hello, It looks like data plane has been restarted. Please generate tech support files from both firewalls and open a case with support please. Regards, Hari Yadavalli

hyadavalli · ‎03-09-2015

Hello, No, it'll use the previous refresh output results(If that was successful) or the previous cached output. Regards, Hari Yadavalli

hyadavalli · ‎03-06-2015

Hello Emma, It depends on the policy pushed to the client machine whether word process is protected or not. If it is then yes, Traps will detect the exploit and won't display the file. Regards, Hari Yadavalli

hyadavalli · ‎03-05-2015

Hello COS, how often the PA query IANA to get the info????? This is updated through dynamic updates(Apps&Threats) installed on the firewall. any way to force this queries???? No Regards, Hari Yadavalli

hyadavalli · ‎03-05-2015

Hello Gonzalo, panHAConfigFailureTrap: HA configuration push to peer has failed This is when user manually syncs the configuration using GUI or CLI command panHAConfigNotSynchTrap: HA config not automatically synched This is when active firewall pushes config sync by itself Ex: When you do a commit on active firewall, after commit success, active firewall pushes configuration to passive without manual sync Hope this clarifies. Regards, Hari Yadavalli

hyadavalli · ‎03-05-2015

Hello, Have you tried changing the area 0 to something else so those two areas won't talk because there is no backbone area? Regards, Hari Yadavalli

hyadavalli · ‎03-05-2015

Hello, You can try as below screenshot. REgards, Hari Yadavalli

hyadavalli · ‎03-04-2015

Hello, What is the service route specified for syslog? 'Device->Setup->Services->Service route configruation' Regards, Hari Yadavalli

hyadavalli · ‎02-25-2015

Hello Rajesh, May I know the upgrade path? Regards, Hari Yadavalli

hyadavalli · ‎02-25-2015

Hello Arnaud, What is the action set for 'smb' decoder in antivirus profile? Regards, Hari Yadavalli

hyadavalli · ‎02-20-2015

Hello, Have you tried selecting File type as cab in file blocking profile with action set to Forward to see if wildfire detects malware? Regards, Hari Yadavalli

hyadavalli · ‎02-20-2015

Hello Sven, One way to verify is check in the current user for the machine which got connected('Network->Global Protect->Gateways->Remote Users') without credentials and look for that IP address in system logs to see whether has any authentication passed onto portal? Regards, Hari Yadavalli

hyadavalli · ‎02-13-2015

Hello John, As far as I know you can do an exception based on application and specify whatever action you want but not specific to an ID for antivirus profile. Regards, Hari Yadavalli

hyadavalli · ‎02-05-2015

Hello Komure, I'm not quite sure what's your questions is. As of my understanding UDLD is cisco propreitary protocol. Regards, Hari Yadavalli

hyadavalli · ‎02-04-2015

Hello Martin, Please add below URLs in allow list: addons.mozilla.org addons.mozilla.org/ addons.cdn.mozilla.net/ Regards, Hari Yadavalli

hyadavalli · ‎02-04-2015

Hello Diego, If you are not implementing ssl-decryption and want to do custom url-filtering for encrypted sites please take a look at the certificate of the sites and use the "CN-name" or "Issued-to" in Custom URL category to block or allow those URLs. Hope this helps. Regards, Hari Yadavalli

hyadavalli · ‎02-04-2015

Hello , Please try the following command in configure mode to delete the authentication profile and assign ip-address to management interface. >configure #delete deviceconfig system authentication-profile #set deviceconfig system ip-address <ip-address> default-gateway <gateway-address> netmask <net-mask> #commit Regards, Hari Yadavalli

hyadavalli · ‎11-21-2014

Hello, I have copied around 40 commands and pasted in putty and it took it with no issues. I tried with set mode using below command >set cli config-output-format set Regards, Hari Yadavalli

hyadavalli · ‎10-31-2014

Hello Renan, My apologies, I stand corrected. For any http or https links in an email body firewall does not check virus database because firewall cannot hash links and so it has to send any links to wildfire and should get a report. Once the firewall receives a report then you will receive wildfire report via email. Regards, Hari Yadavalli

hyadavalli · ‎10-31-2014

Hello Renan, And also another point to note if we already have the signature in our Virus database firewall won't even forward to wildfire. Regards, Hari Yadavalli

hyadavalli · ‎10-31-2014

Hello Renan, Share the output of below command: >show wildfire statistics Regards, Hari Yadavalli

hyadavalli · ‎10-31-2014

Hello Renan, Wildfire email link analysis is no different compared to other file types you have in file blocking profile. If any email contains a http or https link then firewall will forward that link to wildfire and gets an analysis report. If the link in email is benign or malware then firewall will send an email report. Regards, Hari Yadavalli

hyadavalli · ‎10-31-2014

Hello Renan, Do you see the wildfire log show as benign or Malware? Once firewall get the verdict then firewall will send an email alert. Regards, Hari Yadavalli

hyadavalli · ‎10-29-2014

Hello, Enable logging to SSH session and issue any of the below commands, in that way you'll have all the policies logged onto a fileand from there you can print. >show running security-policy OR >configure #show rulebase security Regards, Hari Yadavalli

Date Registered	‎11-08-2012 09:47 AM
Date Last Visited	a week ago
Total Messages Posted	416
Total Likes Received	34

Online Status	Offline
Date Last Visited	a week ago

Strata

Prisma

Cortex

About hyadavalli