How to Post a LIVEcommunity Discussion

[jforsythe]

Are you ready to become a conversation starter?

If you have searched for an answer, topic, or query and have not found what you’re looking for, then your next step might be to post a discussion. There are many ways to post a message to the discussion areas on the LIVEcommunity. Let’s go through them together. 

Posting a Discussion from the Homepage

 

You can start a conversation from the main LIVEcommunity page by clicking the "Start a conversation" button.

Please be sure to select a discussion area that matches what you would like to post this new discussion to, as there are many discussion areas in the LIVEcommunity.

Starting a Discussion in a Board 

Another way is to start a conversation is to go directly to the board where you want to post. You can do this under Collaboration > Discussion. You will see there is everything from General Topics to more than a dozen technologies and tools.

• Once inside the area you need, Click the Start a conversation button at the top of the page.
• In the Subject field, enter your message title. Tip: Make your subject clear and concise, as it is the only part of the message that shows up on the message-listing page.
• In the Body field, type your message. Be sure to include all necessary details, especially, for technical topics.
• Format and spell check your message, as needed. You even have an area to drag and drop any files that may help others answer your questions.
• Click Post to post your topic or Cancel to abandon the new message.

Note: By default, the "Email me when someone replies" option is selected. If you do not want to be notified about any responses, you have to uncheck this option in the upper part of the window.

How to Reply to a Discussion

While inside of a post, simply click the Reply button to respond to a particular post. You are now part of the conversation—kudos!

---

UP NEXT — Step 6: How to Recognize an Accepted Solution

← Return to the Welcome Guide

[ChetanR]

Hi Team,

Activity details in the Application Command Center (ACC) tab only show details based on two previous days when we select the time frame for more than two days (7 Days, in this case). However, in the Network monitor, we are able to view the activity details for applications for the given time frame. 

Please provide a solution for what is causing this issue.

We have started the debug management server 

[New-Memeber]

Hello all,

I'm new her and with Paloalto firewalls.

anyone knows what is the default username and password PANOS vmware I use on GNS3 please.

see below.

Enter 'maint' for boot menu.
Booting PANOS (sysroot0) after 5 seconds...

Entry:
Booting 'PANOS (sysroot0)'

root (hd0,1)
Filesystem type is ext2fs, partition type 0x83
kernel /boot/vmlinuz ro root=/dev/sda2 init=/sbin/init_single_core conso
0,9600n8 console=tty0 quiet alternate_root=/dev/vda2 alternate_root=/dev
hugepages=0
[Linux-bzImage, setup=0x3c00, size=0x38c710]

cpld cpld.1536: Failed to request region 0x600-0x63f

eth0 Link encap:Ethernet HWaddr 0C:4E:C7:46:00:00
inet addr:192.168.17.131 Bcast:192.168.17.255 Mask:255.255.255.0
inet6 addr: fe80::e4e:c7ff:fe46:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:160 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:14692 (14.3 KiB) TX bytes:1026 (1.0 KiB)

[akilan.r@tutelartechlabs.com.panwpartner]

Hello All,

This is my topology I have configured Clientless VPN hosting two application as, paloaltonetworks.com (external-application) and amazon.forest.in (internal hosted application). But i am unable to access the application that hosted inside. In this question have attached my configuration also.  other than that there is no sent byte for clientless-VPN traffic also.

External application works but no sent bytes ?

ISSUE NOTE : 1.External Application working but there is no sent bytes

                         2.Internal Application not accessible