Azure Network Watcher VM extension?

Hello... is it possible to install that Azure Network Watcher VM extension to enable traces and packet captures from the PA VM to the Azure gateway?  It would be handy to help troubleshoot connectivity issues between the PA and the GW.  Thank you.

ESXI Server - Inside Host is on Same Port Group as Palo Alto FW Inside Interface and Pings are failing from all inside hosts

I have a ESXI Server with firewall (Inside, DMZ and Outside) zones

Palo Alto has a rule to allow interzone traffice from inside to outside

Palo Alto has NAT configured for Outside Interface

When I try to ping from host to host on in the same port g

problems to configure internal load balancer on GCP

Hi team, we are working in a lab environment, following the recommended architecture manual:

https://www.paloaltonetworks.com/apps/pan/public/downloadResource?pagePath=/content/pan/en_US/resources/guides/gcp-shared-vcp-deployment-guide

We have followed

Incomplete error

I have a Linux VM trying to send traffic over port 25 smtp and I am getting an incomplete message on the PAN-VM. I have done a few tests with port 587 and works fine, I have gone through the rules in focus detail to verify the rule should allow it bu

GRE Tunnel is not Coming UP

We've created eight GRE tunnels and it's working fine. But when going to create another Tunnel, the tunnel is not coming up. We've tried to changing the remote site router, but no luck.

VM-Series License limits - VIrtual Routers

I have seen documentation outlining the differences in the number of Rules, VPNs, sessions and zones for each VM-Series license, but i think there are also limits on the number of Virtual Routers you can create on each VM license.

Is there any documen

AWS secondary CIDR on VPC ability to NAT to PAN in original CIDR

Hey all,

It has finally happened and we ran out of IPv4 space on Primary CIDR block for our VPC. We created a new CIDR and associated it to the same VPC. However it appears that I can't associate an ENI in the new CIDR to our Palo Alto in the original

VM-Series firewalls in Azure with multiple private zone NICs behind Internal LB not maintaining session

I have a use-case: There are 2 VM-Series Palo-alto firewalls deployed in Azure behind Internal Load Balancer. Each firewall has 3 private zone interfaces and Internal LB has 3 Frontend-IPs, one for each firewall interface subnet, the request traffic

Site to site VPN tunnel in Azure

We need to build a site to site tunnel between on premise and Azure cloud so we are planning to use Palo Alto firewall in Azure,  since we have a requirement to hide VNET subnet in cloud as well as in on premise subnets from each other while sending

VM-Series High Availability on ESXi?

Hi there, I am really new in network virtualization. I want to ask about high availability in Palo Alto VM-Series. We are going to buy two VM-200 (1 for Internal, 1 for External) and will install it on ESXi. I want ask for your advice.

1.Should I buy

Palo Alto 10.0 firewall in HA in Azure

Hi, 

We are trying to test VM series firewall in HA without load-balancer and following the documentation listed on PA website, can someone confirm if the document is well tested and we are seeing issues in connectivity and Template for secondary fir

S2S VPN from PAloAlto to azure cloud

Hi 

we would like to S2S VPN from plaotAlto to Azure cloud  

Azure InterfaceEndpoint Routes Bypassing Palo Alto Firewall

Situation:  Deployed two Palo Alto VM firewalls in Azure in a 'Transit VNet' following the Palo Alto Networks design, https://www.paloaltonetworks.com/resources/reference-architectures/azure.  

When you peer a VNet to the Transit VNet, the remote VN

Panorama network and device templates not syncing to firewall

Hello,

We are trying to set up a new deployment in AWS consisting of two firewalls managed by a Panorama server. 

For starters, we deployed one firewall and one Panorama instance. They are in the same VPC, different subnets. Security groups currently

Policy is not getting pushed

when we are trying to do policy push from Panoroma to firewalls it is getting failed and firewall is seen in out of sync state