jumping from 8.0.17 to 8.1.7 directly?

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

jumping from 8.0.17 to 8.1.7 directly?

L2 Linker

can i upgrade from 8.0.17 to 8.1.7 directly? also would going to 8.1.7 change any of my current config? 

9 REPLIES 9

L4 Transporter

@chuckles Yes, you can. As long as you have 8.1.0 downloaded, you can install the 8.1.7 and it will need only one reboot. 

 

The configuration update is normally designed to be compatible with your current configuraiton as much as possible. Based on experience, I have never had any issues with upgrades from 8.0.x to 8.1.x, but as normal, you should always review the release notes and upgrade procedure before planning the task. 

I made the jump without issue. Just be sure to have 8.1.0 downloaded as well.

Cyber Elite
Cyber Elite

@chuckles,

I would follow the recommended upgrade path just to ensure that you don't run into any issues at all. The issue with not installing 8.1.0 (usually on smaller/older hardware) is that the firewall needs to explode both the base image and the target maintenance release to build a working install image. That isn't a difficult task, but as the software images have gotten larger this process takes up more disk and some of the older hardware and smaller hardware simply can't free up enough disk space to build a functional image.

 

1) Download and install the latest maintenance relase.

2) Download and install the base image.

3) Download and install the target maintenance release.

 

It's likely that simply have the base image downloaded and letting the two images build a functional install image would be fine as long as you've verified that you actually have enough disk space for the firewall/panorama to actually perform that process. I would still recommend following the current recommendation to ensure that your upgrade process goes smoothly,  especially when the OP fails to mention the model they are upgrading. 

I would NOT install 8.1. There are many bugs in 8.1 that don't get resolved until later versions. I have seen bugs listed that specifically say that it can cause problems on upgrade. I would download 8.1, but then download and install 8.1.8-h5, which is the current recommended version.

@khsieh,

You don't run with 8.1 installed and actually running your firewall for any length of time, you immediately perform the upgrade to your target maintenance release. 

 

I'll state it again, but you can follow the old upgrade model where you only needed to download the base image if you want IT IS NOT BEST PRACTICE to do so. If the upgrade breaks your device because your disk ran out of space building a complete install image, tough nuggets.

 

The recommended upgrade path for migrating to 8.1 is the following:

1) Download and install 8.0.19 (as it's the latest maintenance relase). 

2) Reload

3) Download 8.1.0 and 8.1.7 (remove any other image you may have installed except for 8.0.19)

4) Install 8.1.0 (you do not need to reload)

5) Install 8.1.7

6) Reload

7) Verify the device is functioning as intended.

 

I will follow your path.

As i am upgrading all PA to 8.1.9 from 8.0.15.

 

Is it recommended to install 8.1.9?

MP

Help the community: Like helpful comments and mark solutions.

@MP18,

Technically at this point in time 8.1.9 is not a recommended release. That being said, I haven't run into any new issues with 8.1.9 that weren't present in 8.1.8. I'm in the process of upgrading all of my managed firewalls to 8.1.9 and haven't run into any issues effecting production traffic. 

If you have a 5200 series HA pair and are thinking of running 8.1.7 or 8.1.8, be aware of the bugs discussed in this thread:

 

https://live.paloaltonetworks.com/t5/General-Topics/Bug-8-1-7-8-1-8-PA-5200-AUX-Ports/td-p/262440

  • 8085 Views
  • 9 replies
  • 0 Likes
Like what you see?

Show your appreciation!

Click Like if a post is helpful to you or if you just want to show your support.

Click Accept as Solution to acknowledge that the answer to your question has been provided.

The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!

These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the LIVEcommunity as a whole!

The LIVEcommunity thanks you for your participation!