SendSlow and SendHuman syntax explanation

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
PAM Self-Hosted Articles
3 min read
L1 Bithead
No ratings
What does the syntax of the SendSlow & SendHuman parameters mean?

Steps

There is no external documentation on these parameters as Idira does not recommend making changes to these values unless recommended under the guidance from the Support or the Security Services Teams. These settings are set in the 'process' file for those platforms that use the PMTerminal engine. 

SendSlow
This parameter sends information at a fixed stable rate. 
This list contains the following two elements: 
1. The first element controls the number of characters sent to the remote machine. 
2. The second element controls the delay in seconds between each time that information is sent. 
You can use fractions in the second element to specify a delay that is less than a second. 

SendHuman

The following list describes in detail each value of the SendHuman parameter. 
This list contains the following five elements: 
1. The default average send time in seconds of characters. 
2. The average send time in seconds of characters at words ending. 
3. The measure of variability where 0.1 is quite variable, 1 is reasonably variable, and 10 is almost invariable. 
4. The minimum send time that can be used. 
5. The maximum send time that can be used. 

If both SendHuman and SendSlow are specified then SendHuman will be used.

Possible values are:
SendSlow=1 .001
SendSlow=1 .005
SendSlow=1 .01
SendSlow=1 .05
SendSlow=1 .1
SendSlow=1 .5
SendSlow=1 1
SendSlow=2 .01
SendSlow=2 .1

SendHuman=.1 .3 1 .05 2
SendHuman=.1 .1 10 .05 .05
SendHuman=.05 .05 10 .05 .05

Please be advised, changing the values for these parameters can and will break everything on a platform if not made carefully, it is always recommended to discuss these changes with Idira prior to making them.

Note: these settings are for the legacy Unix via SSH CPM plug-in (non TPC) Q:
 
What does the syntax of the SendSlow & SendHuman parameters mean? 
 
A:
 
There is no external documentation on these parameters as Idira does not recommend making changes to these values unless recommended under the guidance from the Support or the Security Services Teams. These settings are set in the 'process' file for those platforms that use the PMTerminal engine. 
 
SendSlow
This parameter sends information at a fixed stable rate. 
This list contains the following two elements: 
1. The first element controls the number of characters sent to the remote machine. 
2. The second element controls the delay in seconds between each time that information is sent. 
You can use fractions in the second element to specify a delay that is less than a second. 
 
SendHuman
The following list describes in detail each value of the SendHuman parameter. 
This list contains the following five elements: 
1. The default average send time in seconds of characters. 
2. The average send time in seconds of characters at words ending. 
3. The measure of variability where 0.1 is quite variable, 1 is reasonably variable, and 10 is almost invariable. 
4. The minimum send time that can be used. 
5. The maximum send time that can be used. 
 
If both SendHuman and SendSlow are specified then SendHuman will be used.

Possible values are:
SendSlow=1 .001
SendSlow=1 .005
SendSlow=1 .01
SendSlow=1 .05
SendSlow=1 .1
SendSlow=1 .5
SendSlow=1 1
SendSlow=2 .01
SendSlow=2 .1

SendHuman=.1 .3 1 .05 2
SendHuman=.1 .1 10 .05 .05
SendHuman=.05 .05 10 .05 .05
 
Please be advised, changing the values for these parameters can and will break everything on a platform if not made carefully, it is always recommended to discuss these changes with Idira prior to making them.
Rate this article:
  • 4140 Views
  • 0 comments
  • 0 Likes
Article Dashboard
Version history
Last Updated:
‎11-05-2026 12:06 PM
Updated by: