How to determine link and transceiver status on AUX ports on a PA 5220 via CLI

cancel
Showing results for 
Search instead for 
Did you mean: 

How to determine link and transceiver status on AUX ports on a PA 5220 via CLI

L2 Linker

I am trying to figure out how to determine the link and transceiver status on the AUX ports on a PA 5220, when used in HA1 mode.

 

I know that via the CLI, you can determine the transceiver status with the following command, but I do NOT see the AUX ports listed:

 

show system state filter sys.s1.p*.phy

 

Is there another CLI command to show link and transceiver status on the AUX ports?

 

Thanks.

Clarke

 

1 ACCEPTED SOLUTION

Accepted Solutions

Cyber Elite
Cyber Elite

that command is for dataplane interfaces, aux is hooked to the system

 

you can see which interfaces aux-1 and aux-2 are bound to with this command:

admin@PA-5220> show system state filter cfg.aux_intf.map

cfg.aux_intf.map: { 'aux-1': eth5, 'aux-2': eth6, }

you can then lookup both interfaces:

admin@PA-5220> show system state filter net.s0.eth5.*

net.s0.eth5.cfg: { 'disable-dhcp': True, 'fips-gated': True, 'hwaddr': d4:f4:be:c3:d8:06, 'ifindex': 7, 'ip-type': static, 'mtu': 1500, 'onboot': True, 'routes': { 'default': , }, 'table': aux-1, 'up': True, 'v6routes': { 'de
fault': , }, }
net.s0.eth5.dhcp-dns: { }
net.s0.eth5.dhcp-ntp: { }
net.s0.eth5.dhcp-opcmd: 0
net.s0.eth5.dhcp-options: { }
net.s0.eth5.hwcfg: { 'advertised': [ ], 'link': Down, 'mode': Force, 'setting': 1Gb/s-full, }
net.s0.eth5.stats: { 'rx-bytes': 0, 'rx-compressed': 0, 'rx-drop': 0, 'rx-errs': 0, 'rx-fifo': 0, 'rx-frame': 0, 'rx-multicast': 0, 'rx-packets': 0, 'tx-bytes': 0, 'tx-carrier': 0, 'tx-colls': 0, 'tx-compressed': 0, 'tx-drop'
: 0, 'tx-errs': 0, 'tx-fifo': 0, 'tx-packets': 0, }

admin@PA-5220> show system state filter net.s0.eth6.*

net.s0.eth6.cfg: { 'disable-dhcp': True, 'fips-gated': True, 'hwaddr': d4:f4:be:c3:d8:07, 'ifindex': 8, 'ip-type': static, 'mtu': 1500, 'onboot': True, 'routes': { 'default': , }, 'table': aux-2, 'up': True, 'v6routes': { 'de
fault': , }, }
net.s0.eth6.hwcfg: { 'advertised': [ 1Gb/s-full, auto, ], 'link': Down, 'mode': Autoneg, 'setting': 1Gb/s-full, }
net.s0.eth6.stats: { 'rx-bytes': 0, 'rx-compressed': 0, 'rx-drop': 0, 'rx-errs': 0, 'rx-fifo': 0, 'rx-frame': 0, 'rx-multicast': 0, 'rx-packets': 0, 'tx-bytes': 0, 'tx-carrier': 0, 'tx-colls': 0, 'tx-compressed': 0, 'tx-drop'
: 0, 'tx-errs': 0, 'tx-fifo': 0, 'tx-packets': 0, }
Tom Piens
PANgurus

View solution in original post

1 REPLY 1

Cyber Elite
Cyber Elite

that command is for dataplane interfaces, aux is hooked to the system

 

you can see which interfaces aux-1 and aux-2 are bound to with this command:

admin@PA-5220> show system state filter cfg.aux_intf.map

cfg.aux_intf.map: { 'aux-1': eth5, 'aux-2': eth6, }

you can then lookup both interfaces:

admin@PA-5220> show system state filter net.s0.eth5.*

net.s0.eth5.cfg: { 'disable-dhcp': True, 'fips-gated': True, 'hwaddr': d4:f4:be:c3:d8:06, 'ifindex': 7, 'ip-type': static, 'mtu': 1500, 'onboot': True, 'routes': { 'default': , }, 'table': aux-1, 'up': True, 'v6routes': { 'de
fault': , }, }
net.s0.eth5.dhcp-dns: { }
net.s0.eth5.dhcp-ntp: { }
net.s0.eth5.dhcp-opcmd: 0
net.s0.eth5.dhcp-options: { }
net.s0.eth5.hwcfg: { 'advertised': [ ], 'link': Down, 'mode': Force, 'setting': 1Gb/s-full, }
net.s0.eth5.stats: { 'rx-bytes': 0, 'rx-compressed': 0, 'rx-drop': 0, 'rx-errs': 0, 'rx-fifo': 0, 'rx-frame': 0, 'rx-multicast': 0, 'rx-packets': 0, 'tx-bytes': 0, 'tx-carrier': 0, 'tx-colls': 0, 'tx-compressed': 0, 'tx-drop'
: 0, 'tx-errs': 0, 'tx-fifo': 0, 'tx-packets': 0, }

admin@PA-5220> show system state filter net.s0.eth6.*

net.s0.eth6.cfg: { 'disable-dhcp': True, 'fips-gated': True, 'hwaddr': d4:f4:be:c3:d8:07, 'ifindex': 8, 'ip-type': static, 'mtu': 1500, 'onboot': True, 'routes': { 'default': , }, 'table': aux-2, 'up': True, 'v6routes': { 'de
fault': , }, }
net.s0.eth6.hwcfg: { 'advertised': [ 1Gb/s-full, auto, ], 'link': Down, 'mode': Autoneg, 'setting': 1Gb/s-full, }
net.s0.eth6.stats: { 'rx-bytes': 0, 'rx-compressed': 0, 'rx-drop': 0, 'rx-errs': 0, 'rx-fifo': 0, 'rx-frame': 0, 'rx-multicast': 0, 'rx-packets': 0, 'tx-bytes': 0, 'tx-carrier': 0, 'tx-colls': 0, 'tx-compressed': 0, 'tx-drop'
: 0, 'tx-errs': 0, 'tx-fifo': 0, 'tx-packets': 0, }
Tom Piens
PANgurus
Like what you see?

Show your appreciation!

Click Like if a post is helpful to you or if you just want to show your support.

Click Accept as Solution to acknowledge that the answer to your question has been provided.

The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!

These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the LIVEcommunity as a whole!

The LIVEcommunity thanks you for your participation!