HSBI and HA

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Palo Alto Networks Approved
Palo Alto Networks Approved
Community Expert Verified
Community Expert Verified

HSBI and HA

L2 Linker

Folks,

I would like understand the difference between HSBI and HA1, HA1B, HA2, HA2B 

As per my understanding

HA1 for control & HA1B for backup link

HA2 for data & HA2B for backup link 

control carries  heartbeats and communication 

Dara traffic carries Ip table, arp table, session table? Is that correct?

 

For state full session sync up we “must” use HSBI link? Or it can be used for over HA2?

 

I have little expertise in PA, but I never see such implementation?

can you please clarify?

your swift response is much appreciated 

3 accepted solutions

Accepted Solutions

Cyber Elite
Cyber Elite

HA1 is the 'brains' of the HA cluster, sharing configuration, routing information, control messages to see if the peer is alive and functional, etc. 

HA1b is a backup link (if for some reason HA1 is disconected but both firewalls are still fully functional, they will assume the remote peer is down and both start accepting packets at the same time, this is not fun to have happen, so make sure to set up HA1b)

 

HA2 is where the session table gets synced so if a firewall goes down the perr can pick up existing sessions

ha2b is the backup link

you are not required to use the HSCI link, you can assign the type 'HA' to dataplane interfaces and use those instead

you cannot use HSCI for HA1 connections, but you should either use the dedidicated HA1a/HA1b, the AUX1/AUX2, or dataplane interfaces (dedicated links preferred)

 

Tom Piens
PANgurus - Strata specialist; config reviews, policy optimization

View solution in original post

I have two 1410 firewall. I have connected two cables on HA1a, HA1b and HSCI. Now should I use HSCI port for HA2 communication?  In fact, its forcibly selected HSCI for HA2 communication, please help me understand. 

My second question is its not mandate to configure IP for HA2 correct? And HA1 we need give same IP under the general settings?

View solution in original post

Hi @Ramakrishnan,

Please check the following documentations -
https://docs.paloaltonetworks.com/hardware/pa-1400-hardware-reference/pa-1400-series-overview/front-... 
https://docs.paloaltonetworks.com/pan-os/10-1/pan-os-admin/high-availability/ha-concepts/ha-links-an...
HSCI is high speed interface, which main purpose is to be used for HA2. As @reaper  already mentined HA2 is data link, it is used to sync session information between the two HA members. (and also forward traffic in case you use active/active).

So if you have the physical capability to connect both member directly (no routers, no switches, no other intermediate devices), it is always recommend to  use the HSCI for HA2.

 

If you cannot connect both peer directly, you can reserve one of the data plane interfaces for HA and then configure HA2 to use that dataplane interface. By default no dataplane interface is being reserved for HA, that is why when you try to edit HA your dropdown offers only HSCI.

Regarding the IP addresses:

- As you can see from above links HSCI is layer1 interface, so must use "ethernet" for HA2 transport, which used PAN custom/properiotry ethernet frames which doesn't use IP address. So even if you set some addresses they will be ignored if transport is set to ethernet

Transport
—Choose one of the following transport options:

    Ethernet
    —Use when the firewalls are connected back-to-back or through a switch (Ethertype 0x7261).
    IP
    —Use when Layer 3 transport is required (IP protocol number 99).
    UDP
    —Use to take advantage of the fact that the checksum is calculated on the entire packet rather than just the header, as in the IP option (UDP port 29281). The benefit of using UDP mode is the presence of the UDP checksum to verify the integrity of a session sync message.

 

For HA1 you must use IP addresses and you must have different addresses for each member. If you connect them directly you have to specify the same subnet. If they are not connected directly you should configure a gateway which will route between the two networks.

View solution in original post

5 REPLIES 5

Cyber Elite
Cyber Elite

HA1 is the 'brains' of the HA cluster, sharing configuration, routing information, control messages to see if the peer is alive and functional, etc. 

HA1b is a backup link (if for some reason HA1 is disconected but both firewalls are still fully functional, they will assume the remote peer is down and both start accepting packets at the same time, this is not fun to have happen, so make sure to set up HA1b)

 

HA2 is where the session table gets synced so if a firewall goes down the perr can pick up existing sessions

ha2b is the backup link

you are not required to use the HSCI link, you can assign the type 'HA' to dataplane interfaces and use those instead

you cannot use HSCI for HA1 connections, but you should either use the dedidicated HA1a/HA1b, the AUX1/AUX2, or dataplane interfaces (dedicated links preferred)

 

Tom Piens
PANgurus - Strata specialist; config reviews, policy optimization

I have one last doubt/clarity. 

If we run HA1 and HA2 between firewalls as below back-to-back links. 

[FW1 HA1 < --- > FW2 HA1] - No backup link considered 

[FW1 HA2 < -- >  FW2 HA2] - No backup link considered 

So No need of HSCI, since all session sync up will happen over HA2 ? So during Active device fails passive will become active and pick up the session, from an end-user perspective no need for session reinitiation? Is my understanding correct?

 

 

I have two 1410 firewall. I have connected two cables on HA1a, HA1b and HSCI. Now should I use HSCI port for HA2 communication?  In fact, its forcibly selected HSCI for HA2 communication, please help me understand. 

My second question is its not mandate to configure IP for HA2 correct? And HA1 we need give same IP under the general settings?

Hi @Ramakrishnan,

Please check the following documentations -
https://docs.paloaltonetworks.com/hardware/pa-1400-hardware-reference/pa-1400-series-overview/front-... 
https://docs.paloaltonetworks.com/pan-os/10-1/pan-os-admin/high-availability/ha-concepts/ha-links-an...
HSCI is high speed interface, which main purpose is to be used for HA2. As @reaper  already mentined HA2 is data link, it is used to sync session information between the two HA members. (and also forward traffic in case you use active/active).

So if you have the physical capability to connect both member directly (no routers, no switches, no other intermediate devices), it is always recommend to  use the HSCI for HA2.

 

If you cannot connect both peer directly, you can reserve one of the data plane interfaces for HA and then configure HA2 to use that dataplane interface. By default no dataplane interface is being reserved for HA, that is why when you try to edit HA your dropdown offers only HSCI.

Regarding the IP addresses:

- As you can see from above links HSCI is layer1 interface, so must use "ethernet" for HA2 transport, which used PAN custom/properiotry ethernet frames which doesn't use IP address. So even if you set some addresses they will be ignored if transport is set to ethernet

Transport
—Choose one of the following transport options:

    Ethernet
    —Use when the firewalls are connected back-to-back or through a switch (Ethertype 0x7261).
    IP
    —Use when Layer 3 transport is required (IP protocol number 99).
    UDP
    —Use to take advantage of the fact that the checksum is calculated on the entire packet rather than just the header, as in the IP option (UDP port 29281). The benefit of using UDP mode is the presence of the UDP checksum to verify the integrity of a session sync message.

 

For HA1 you must use IP addresses and you must have different addresses for each member. If you connect them directly you have to specify the same subnet. If they are not connected directly you should configure a gateway which will route between the two networks.

Thanks for answering, I appreciate you, you made my day.

  • 3 accepted solutions
  • 3138 Views
  • 5 replies
  • 0 Likes
Like what you see?

Show your appreciation!

Click Like if a post is helpful to you or if you just want to show your support.

Click Accept as Solution to acknowledge that the answer to your question has been provided.

The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!

These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the LIVEcommunity as a whole!

The LIVEcommunity thanks you for your participation!