Mgmt interface stop working

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Announcements

Mgmt interface stop working

L1 Bithead

Hi.

 

I have a PA-500 and after a storm, the management interface stopped work. When I connect a network cable the leds doesn't work.

I made a configuration to access the Firewall and to use some services throught another interface, but the "Log Scheduled Export" doesn't have this option.

How can I solv this problem?

19 REPLIES 19

Cyber Elite
Cyber Elite

Hi,

 

When you say storm what do you mean?

Is the settings on the Management interface correct like speed and duplex to which it connects on switch port?

 

When you run the command --

show interface management

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-------------------------------------------------------------------------------
Name: Management Interface
Link status:
Runtime link speed/duplex/state: 1000/full/up
Configured link speed/duplex/state: auto/auto/auto

 

 

what does you see?

 

 

 

MP

Help the community: Like helpful comments and mark solutions.

Hi.

I mean there was a heavy rain and some boltz. After that, the management interface stopped working. I changed the port, changed the switch, but the leds of the mgmt port doesn't work.

I have access to the firewall through the gateway port.

_____________________________________

Name: Management Interface
Link status:
Runtime link speed/duplex/state: unknown/unknown/down
Configured link speed/duplex/state: 100/full/auto

In your output i see speed as 100

What are settings on the switch port?

 

is this fast ethernet  port?

MP

Help the community: Like helpful comments and mark solutions.

It is a Cisco 2960X

 

#show int

Gi1/0/1 ## MNGT-PALO ## notconnect 1 auto auto 10/100/1000BaseTX

 

#show run

interface GigabitEthernet1/0/1
description ## MNGT-PALO ##
switchport mode access
spanning-tree portfast

I catch this from the log of the switch:

Jan 20 17:57:25.050: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to up
Jan 20 17:57:27.822: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
Jan 20 17:57:36.172: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to up
Jan 20 17:57:39.052: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
Jan 20 17:57:52.694: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to up
Jan 20 17:57:58.098: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
Jan 20 17:58:06.738: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to up

Try to hard code speed on PA and switch  to 1000.

 

PA

 

1# set deviceconfig system speed-duplex 1Gbps-full-duplex ip-address x.x.x.x  netmask x.x.x.x

Also please double check the Ethernet cable.

 

 

MP

Help the community: Like helpful comments and mark solutions.

I changed the speed and the cable, but the problem still the same.

 

Name: Management Interface
Link status:
Runtime link speed/duplex/state: unknown/unknown/down
Configured link speed/duplex/state: 1000/full/auto

If you connect your laptop to Management port does it shows up then?

MP

Help the community: Like helpful comments and mark solutions.

Doesn't shows up 😞

Then it seems some hardware issue with port.

Did you try to reboot the device ?

MP

Help the community: Like helpful comments and mark solutions.

Yes, I tried.

 

Can I use another interface to use the resource "Scheduled Log Export"?

Under device setup

 

services

service route config 

 

Then click on customize there you can choose feature which you want like email then choose the data port

MP

Help the community: Like helpful comments and mark solutions.

I've already did this, I changed all features to source int 1/1.1 and gateway address, but the "Scheduled Log Export" doesn't work.

which feature you have selected ?

MP

Help the community: Like helpful comments and mark solutions.
  • 9085 Views
  • 19 replies
  • 0 Likes
Like what you see?

Show your appreciation!

Click Like if a post is helpful to you or if you just want to show your support.

Click Accept as Solution to acknowledge that the answer to your question has been provided.

The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!

These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the LIVEcommunity as a whole!

The LIVEcommunity thanks you for your participation!