- Access exclusive content
- Connect with peers
- Share your expertise
- Find support resources
11-19-2019 03:18 PM
New Panorama 9.0.5 install. Panorama was successfully installed in a VM on a single disk. Needed space for a log volume so a second disk was created and attached to the VM. VM was rebooted, disk added using “request system disk add sdb”, disk is visible via “show system disk details", shows Admin Enabled state.
When attempting to use this volume in “Managed Collectors”, the disk doesn't show when we click Add. Tried multiple reboots to no avail.
11-19-2019 03:56 PM
Problem solved by tech support.
Under "Managed Collectors" add and enter just the serial number of the collector. Commit the changes. Attempt to add a new collector and the disk will appear in the list.
11-19-2019 03:56 PM
Problem solved by tech support.
Under "Managed Collectors" add and enter just the serial number of the collector. Commit the changes. Attempt to add a new collector and the disk will appear in the list.
03-29-2024 01:43 PM
We just updated to 10.2.x and had issues after adding the disk.
We had a similar issue.
The disk would show up in the console (SSH session) and would show ready, but we could not add them to the collector.
After making a minor tweak to an object description and doing a "COMMIT" we were able to add the disk to the collector.
Don't forget to Commit after adding the disks via SSH and after adding to the collector in the GUI.
07-18-2024 04:06 AM
How to add via cli.Please share the commands
08-28-2024 08:34 PM
Panorama> show system disk details
Name : sdb
State : Present
Size : 2097152 MB
Status : Unavailable
Reason : Admin disabled
Panorama> show system disk-partition
Disk /dev/sda: 81 GiB, 86973087744 bytes, 169869312 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xaa2c8c93
Device Boot Start End Sectors Size Id Type
/dev/sda1 2176 2056319 2054144 1003M 83 Linux
/dev/sda2 2097280 18874368 16777089 8G 83 Linux
/dev/sda3 18874496 35651584 16777089 8G 83 Linux
/dev/sda4 35651648 169869311 134217664 64G f W95 Ext'd (LBA)
/dev/sda5 35651712 85983232 50331521 24G 83 Linux
/dev/sda6 85983360 98566144 12582785 6G 83 Linux
/dev/sda7 98566272 102760448 4194177 2G 83 Linux
/dev/sda8 102760576 169869311 67108736 32G 83 Linux
Disk /dev/sdb: 2 TiB, 2199023255552 bytes, 4294967296 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 98323EF7-2679-49BB-8B18-7C48ED8C9D01
Device Start End Sectors Size Type
/dev/sdb1 20480 3706898431 3706877952 1.7T Linux filesystem
Disk /dev/loop0: 10 GiB, 10737418240 bytes, 20971520 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Panorama> request system disk add sdb
Executing this command will delete all data on the drive being added. Do you want to continue? (y or n)
This may take few minutes. Run 'show system disk details' to see the status
Panorama> show system disk details
Name : sdb
State : Present
Size : 2097152 MB
Status : Busy
Reason : Add in progress
<...I waited a few minutes...>
Panorama> show system disk details
Name : sdb
State : Present
Size : 2097152 MB
Status : Available
Reason : Admin enabled
12-15-2024 04:15 AM
Team,
We are also unable to add disk in collector in panorama. But if we checked in CLI then it shows present but admin disable.
What is the solution?
12-15-2024 07:06 PM
At the CLI if you do
So you can do
Name
: sdb
State : Present
Size : 2048000 MB
Status : Available
Reason : Admin enabled
Name : sdc
State : Present
Size : 2048000 MB
Status : Available
Reason : Admin disabled
Click Accept as Solution to acknowledge that the answer to your question has been provided.
The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!
These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the LIVEcommunity as a whole!
The LIVEcommunity thanks you for your participation!