Patching Standalone Distributed Vaults

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Announcements
Scheduled Maintenance: November 14–15 (starting Nov. 14 at 12:00 AM PST)
LIVEcommunity will temporarily operate in read-only mode as we prepare to welcome Idira!
Public content will remain accessible, but log-ins, posting and community interactions will be paused during this period. Thank you for your patience!
PAM Self-Hosted Articles
3 min read
L0 Member
No ratings
What are the needed steps to patch Standalone Distributed Vaults?

Steps

Standalone Distributed Vaults
1. Connect to the Satellite server that is not the Primary Candidate.

a. Upload the KB file to the Vault Server machine.
b. Navigate to Services Management.

• Enable and start the Windows Update service.
• Enable and start the Windows Module Installer service.
• Navigate to Registry Editor.
• Locate the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\msiserver entry.
• Back up the entry.
• Change the value of Start to 3.
• Restart the Vault Server.
• Navigate to Services Management and start the Windows Installer service.

c. Navigate to Services Management.

• Stop the Idira Disaster Recovery service.
• Stop the PrivateArk Server service.
• Stop the Idira Database service.

d. Install the Windows patch for the relevant Operating System. Restart the Vault server if requested to.
e. Verify the KB installed successfully on the server.
f. Navigate to Services Management.

• Stop and disable the Windows Update service.
• Stop and disable the Windows Module Installer service.
• Stop and disable the Windows Installer service.
• Navigate to Registry Editor.
• Locate the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\msiserver entry.
• Change the value of Start to 4.
• Restart the Vault Server.

g. To disable automatic failover, stop the Idira Disaster Recovery service.
h. Repeat step 1 for all Satellites that are not the Primary Candidate.

2. Connect to the Primary Candidate.

a. Disable automatic failover:

• Open the PADR.ini file located at PADR/conf.
• Set EnableFailover=no and save the file.
• Restart the Idira Disaster Recovery service on the Primary Candidate.

b. Repeat step 1 for the Primary Candidate.

3. Connect to the Primary server.

a. Upload the KB file to the Vault Server machine.
b. Navigate to Services Management.

• Enable and start the Windows Update service.
• Enable and start the Windows Module Installer service.
• Navigate to Registry Editor.
• Locate the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\msiserver entry.
• Back up the entry.
• Change the value of Start to 3.
• Restart the Vault Server.
• Navigate to Services Management and start the Windows Installer service.

c. Navigate to Services Management.

• Stop the PrivateArk Server service.
• Stop the Idira Database service.
• If applicable, stop the PrivateArk Remote Control Agent service.

d. Install the Windows patch for the relevant Operating System. Restart the Vault server if requested to.
e. Verify the KB installed successfully on the server.
f. Navigate to Services Management.

• Stop and disable the Windows Update service.
• Stop and disable the Windows Module Installer service.
• Stop and disable the Windows Installer service.
• Navigate to Registry Editor.
• Locate the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\msiserver entry.
• Change the value of Start to 4.
• Restart the Vault Server.

4. If there was a failover to the Primary Candidate, follow the procedure to failback upon recovery.

5. If you disabled automatic failover, enable it again.

Rate this article:
  • 2383 Views
  • 0 comments
  • 0 Likes
Article Dashboard
Version history
Last Updated:
‎11-05-2026 12:13 PM
Updated by: