- Access exclusive content
- Connect with peers
- Share your expertise
- Find support resources
Enhanced Security Measures in Place: To ensure a safer experience, we’ve implemented additional, temporary security measures for all users.
04-03-2018 02:54 PM - edited 04-03-2018 02:56 PM
What is the CLI command for viewing transceiver light levels? Palo Alto 7050
05-20-2021 03:15 PM - edited 05-20-2021 10:09 PM
On version PAN OS 10.00 they have feature for transceiver light levels.
how transceiver-detail ethernet1/11
--------------------------------------------------------------------------------
Detailed Transceiver Information
--------------------------------------------------------------------------------
Interface: ethernet1/11
Vendor Name: AVAGO
Vendor Part Number: AFBR-5715PZ Rev
Vendor Serial Number: AM17332V6LD
Link Length for 62.5/125 um OM1 fiber: 270 m
Link Length for 50/125 um OM2 fiber: 550 m
Link Length for 50/125 um OM3 fiber: 0 m
Link Length for 50/125 um OM4 fiber: 0 m
Diagnostic Monitor Information:
--------------------------------------------------------------------------------
Alarms Warnings
High Low High Low
--------------------------------------------------------------------------------
Temperature 0.00 C 3.02 C 7.00 C 0.00 C 1.12 C
Voltage 0.00 V 1.64 V 0.00 V 0.31 V 0.00 V
Current 0.00 mA 28.21 mA 0.00 mA 33.45 mA 33.42 mA
TX Power 0.00 mW 2.03 mW 0.82 mW 0.82 mW 0.82 mW
RX Power 0.00 mW 0.82 mW 0.82 mW 0.00 mW 0.60 mW
--------------------------------------------------------------------------------
Regards
04-04-2018 05:07 AM
I'm not actually sure that this gives you the light levels, but the most detailed command that I've been able to find for individual interfaces is 'show system state filter-pretty sys.sx.py.stats' where X is the slot number and Y is the port number.
04-04-2018 12:53 PM
Thanks for the reply. I have asked for someone to test the command you provided, but not sure how long it will take them. Will post when I know.
04-12-2018 12:02 PM
Still waiting on test of command
04-12-2018 01:14 PM
I was told by PA support that they do not have the feature and no plans to get it. So that means a physical dispatch is required to simply check light levels. Not good.
04-12-2018 01:23 PM
I would check with your SE if there is an active feature request to add this feature into PAN-OS. If there is post it here so that others can add their votes to it 😉
09-11-2019 07:41 AM
Hi All,
We are also having the same situation, however I have raised a ticket with PA support desk. Will update you if I get some positive feedback.
Regards
Binoj Savariyar
09-27-2019 09:52 PM
It is good to have that feature as we will be using HSCI port on PA5220.
Hope PA will add this feature soon
05-20-2021 11:42 AM
How is this not added yet??
Oh Hey Palo Alto Networks I have some amazing info that could bring huge simple improvements with security rule management. please reach out to me.
05-20-2021 03:15 PM - edited 05-20-2021 10:09 PM
On version PAN OS 10.00 they have feature for transceiver light levels.
how transceiver-detail ethernet1/11
--------------------------------------------------------------------------------
Detailed Transceiver Information
--------------------------------------------------------------------------------
Interface: ethernet1/11
Vendor Name: AVAGO
Vendor Part Number: AFBR-5715PZ Rev
Vendor Serial Number: AM17332V6LD
Link Length for 62.5/125 um OM1 fiber: 270 m
Link Length for 50/125 um OM2 fiber: 550 m
Link Length for 50/125 um OM3 fiber: 0 m
Link Length for 50/125 um OM4 fiber: 0 m
Diagnostic Monitor Information:
--------------------------------------------------------------------------------
Alarms Warnings
High Low High Low
--------------------------------------------------------------------------------
Temperature 0.00 C 3.02 C 7.00 C 0.00 C 1.12 C
Voltage 0.00 V 1.64 V 0.00 V 0.31 V 0.00 V
Current 0.00 mA 28.21 mA 0.00 mA 33.45 mA 33.42 mA
TX Power 0.00 mW 2.03 mW 0.82 mW 0.82 mW 0.82 mW
RX Power 0.00 mW 0.82 mW 0.82 mW 0.00 mW 0.60 mW
--------------------------------------------------------------------------------
Regards
01-05-2023 05:02 PM
my Palo 5220 on PanOS 10.2.2 says that's not a command. What am I missing?
01-05-2023 05:36 PM
Just to verify, you are trying 'show' instead of the indicated 'how' correct? The command definitely exists on PAN-OS 10.2 and PAN-OS 11.0 without change.
01-06-2023 10:12 AM
Yes I was doing the show command not the how. But there was another mistake I was doing, I used a saved putty connection and noticed this morning I was connecting to our old palo that is no longer in use and only on OS 9 not 10. Changed to the actual production palo and I was able to use that command. This was my fault for not noticing that. Thanks for the quick reply.
08-28-2023 02:54 PM
Yes but doesn't show light levels
Click Accept as Solution to acknowledge that the answer to your question has been provided.
The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!
These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the LIVEcommunity as a whole!
The LIVEcommunity thanks you for your participation!