CLI command for transceiver light levels

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Announcements
Please sign in to see details of an important advisory in our Customer Advisories area.
Palo Alto Networks Approved
Palo Alto Networks Approved
Community Expert Verified
Community Expert Verified

CLI command for transceiver light levels

L1 Bithead

What is the CLI command for viewing transceiver light levels? Palo Alto 7050

1 accepted solution

Accepted Solutions

@tshooter 

 

On version PAN OS 10.00 they have feature for transceiver light levels.

 

how transceiver-detail ethernet1/11

 

--------------------------------------------------------------------------------

Detailed Transceiver Information

--------------------------------------------------------------------------------

Interface:                             ethernet1/11

Vendor Name:                           AVAGO           

Vendor Part Number:                    AFBR-5715PZ      Rev     

Vendor Serial Number:                  AM17332V6LD     

Link Length for 62.5/125 um OM1 fiber: 270 m

Link Length for 50/125 um OM2 fiber:   550 m

Link Length for 50/125 um OM3 fiber:   0 m

Link Length for 50/125 um OM4 fiber:   0 m

Diagnostic Monitor Information:

--------------------------------------------------------------------------------

                                      Alarms                  Warnings

                                High          Low         High        Low

--------------------------------------------------------------------------------

Temperature        0.00 C       3.02 C        7.00 C      0.00 C      1.12 C

Voltage            0.00 V       1.64 V        0.00 V      0.31 V      0.00 V

Current           0.00 mA     28.21 mA       0.00 mA    33.45 mA    33.42 mA

TX Power          0.00 mW      2.03 mW       0.82 mW     0.82 mW     0.82 mW

RX Power          0.00 mW      0.82 mW       0.82 mW     0.00 mW     0.60 mW

--------------------------------------------------------------------------------

 

 

Regards

MP

Help the community: Like helpful comments and mark solutions.

View solution in original post

13 REPLIES 13

Cyber Elite
Cyber Elite

@mikeatt,

I'm not actually sure that this gives you the light levels, but the most detailed command that I've been able to find for individual interfaces is 'show system state filter-pretty sys.sx.py.stats' where X is the slot number and Y is the port number.  

Thanks for the reply. I have asked for someone to test the command you provided, but not sure how long it will take them. Will post when I know.

Still waiting on test of command

I was told by PA support that they do not have the feature and no plans to get it. So that means a physical dispatch is required to simply check light levels. Not good.

@mikeatt,

I would check with your SE if there is an active feature request to add this feature into PAN-OS. If there is post it here so that others can add their votes to it 😉 

Hi All,

 

We are also having the same situation, however I have raised a ticket with PA support desk. Will update you if I get some positive feedback.

 

Regards

Binoj Savariyar

BS

It is good to have that feature as we will be using HSCI port on PA5220.

Hope PA will add this feature soon

MP

Help the community: Like helpful comments and mark solutions.

How is this not added yet??

Oh Hey Palo Alto Networks  I have some amazing info that could bring huge simple improvements with security rule management. please reach out to me. 

@tshooter 

 

On version PAN OS 10.00 they have feature for transceiver light levels.

 

how transceiver-detail ethernet1/11

 

--------------------------------------------------------------------------------

Detailed Transceiver Information

--------------------------------------------------------------------------------

Interface:                             ethernet1/11

Vendor Name:                           AVAGO           

Vendor Part Number:                    AFBR-5715PZ      Rev     

Vendor Serial Number:                  AM17332V6LD     

Link Length for 62.5/125 um OM1 fiber: 270 m

Link Length for 50/125 um OM2 fiber:   550 m

Link Length for 50/125 um OM3 fiber:   0 m

Link Length for 50/125 um OM4 fiber:   0 m

Diagnostic Monitor Information:

--------------------------------------------------------------------------------

                                      Alarms                  Warnings

                                High          Low         High        Low

--------------------------------------------------------------------------------

Temperature        0.00 C       3.02 C        7.00 C      0.00 C      1.12 C

Voltage            0.00 V       1.64 V        0.00 V      0.31 V      0.00 V

Current           0.00 mA     28.21 mA       0.00 mA    33.45 mA    33.42 mA

TX Power          0.00 mW      2.03 mW       0.82 mW     0.82 mW     0.82 mW

RX Power          0.00 mW      0.82 mW       0.82 mW     0.00 mW     0.60 mW

--------------------------------------------------------------------------------

 

 

Regards

MP

Help the community: Like helpful comments and mark solutions.

my Palo 5220 on PanOS 10.2.2  says that's not a command. What am I missing?

@mduhon,

Just to verify, you are trying 'show' instead of the indicated 'how' correct? The command definitely exists on PAN-OS 10.2 and PAN-OS 11.0 without change. 

Yes I was doing the show command not the how. But there was another mistake I was doing, I used a saved putty connection and noticed this morning I was connecting to our old palo that is no longer in use and only on OS 9 not 10. Changed to the actual production palo and I was able to use that command. This was my fault for not noticing that. Thanks for the quick reply.

Yes but doesn't show light levels

  • 1 accepted solution
  • 13569 Views
  • 13 replies
  • 0 Likes
Like what you see?

Show your appreciation!

Click Like if a post is helpful to you or if you just want to show your support.

Click Accept as Solution to acknowledge that the answer to your question has been provided.

The button appears next to the replies on topics you’ve started. The member who gave the solution and all future visitors to this topic will appreciate it!

These simple actions take just seconds of your time, but go a long way in showing appreciation for community members and the LIVEcommunity as a whole!

The LIVEcommunity thanks you for your participation!