PA-VM 10.2.5 EVE-NG not working - cant Login to CLI or GUI

Hello, We have built an EVE-NG environment for testing purposes. Within this environment we would like to install a PA-VM. For this purpose we have organized a test license from Palo Alto. After successful upload of the image and installation, the login does not work, neither in the GUI nor in the CLI. Unfortunately, no meaningful log appears ei...

VM Series on ESXi not receving OSPF hello packets when connected to EVE-NG

Hello, I have set up a PA-VM version 10.2.5 on VMware ESXi as I was not able to get it to work properly on EVE-NG. On ESXi I did the following: Added new Port Group to the Virtual Switch Added a Network Adapter to PA-VM and associated it to the new Port Group This is to configure an interface as Outside on the FW to connect it to my EVE-NG...

Paloalto virtual image stuck in 'No Bootable Device'

Hello Team,I have downloaded multiple virtual images for Paloalto for EVE-NG. 10.2.3 10.1.8 & 10.1.6. But all of them are giving me same issue which is 'No Bootable Device' and this message stays for hours. All other vendor instances are working fine in EVE-NG (Cisco, F5, ASA, FTD, FMC etc.) Kindly advise.

Can Palo Alto VM HA be achived at at VMware level using VMotion or Fault tolerant? VMware EXSi Hypervisor

Communication between NSX-T Manager and Panorama - User/Service account

Hello Everyone,We are planning to setup VM-Series in host mode for East-West protection in NSX-T. Part of integration between NSX-T and Panorama, we need a user/service account on NSX-T that Panorama will use for integration and synchronization. My question is what roles/permission/privileges that user/service account need? does it have to be ad...

I am migrating a Palo HA pair VM to a new host and I would like to validate the steps if anyone can assist.

I have the following steps laid out. Please have someone verify if this is correct or if I have forgotten anything. I am migrating the HA pair to a new host with vMotion. - We are running vSphere 7.0 (ESXi host migration is 6.5 > 7.0) please confirm if I need to suspend the heartbeat - I read that I need to select "This guest was moved" to pr...

Palo Alto VM300 is not responding to the incoming IKE_SA_INIT request

Hi there, I am experiencing a weird behavior of my VM-Series PA running PanOS 10.0.4 I am trying to construct 2 VPN tunnels. First tunnel is IKEv1 toward CiscoASA. This tunnel is up and running like a charm. However, my second tunnel toward a Google Cloud VPN, using IKEv2, my PA is ignoring the IKE_SA_INIT from the Google. I have check a...

D-NAT Not Working in PA-VM Workstation

Hi, I have deployed PA-VM in workstation, In this the Destination NAT is not working. As per the global counter the packet is dropped on the below counters, Session discarded: unknown application to control plane

PaloAlto Evaluation VM

Dear Community Members, I have received the evaluation VM and I am trying to test it on a VMware workstation but it's giving me these errors. Kindly advise or refer to any possible solution.VM will automatically restart after this error. My configurations are CPU: 2 RAM: 4/8 (tested both) VMware Workstation 16 Thanks, Please note you are po...

Vmware VM with paravirtual controller is supported?

Hello, I want to ask regarding PAN-VM in Vmware. VMs in vmware have LSI disk controllers. Can be these controllers changes to vmware paravirtual? Or is it supported? If no, does anybody know if PAN will support this disk controller? thank you Rudolf

PA-VM-EVAL shutdown automatically after boot

Hi All, Recently I requested an Eval image of Palo alto when I install it just after boot it shows an error "Bits 55-60 of /proc/PID/pagemap entries are about to stop being page-shift some time soon".And after that message it says " stopping pan software" and the VM machine stopped, I start the VM again and it still showing the same message and ...

is the azure Vm-700 certified to run on new Ds5_v5 platiform?

Looking to upgrade from a Vm-500 to a Vm-700 Is the vm-700 certified to run on newer hardware platforms the Ds5_v5 rather than the older V2 platiform. The Vm-700 with Ds5_v2, Dv2, hourly cost is $3.45 (azure marketplace). What other costs do I need to "add in" to get a monthly cost (minus bandwidth that is always a variable) We are Payg...