This website uses Cookies. By clicking Accept, you agree to the storing of cookies on your device to enhance your community and translation experience. Read our Privacy Policy.
Click Preferences to customize your cookie settings.
Accept
Reject
Preferences
Buy or Renew
Buy or Renew
Panorama Discussions
Post discussions about Panorama, a centralized network security management solution for all your Palo Alto Networks firewalls irrespective of their form factors or locations, in this forum.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Panorama Discussions
Post discussions about Panorama, a centralized network security management solution for all your Palo Alto Networks firewalls irrespective of their form factors or locations, in this forum.
About Panorama Discussions
Post discussions about Panorama, a centralized network security management solution for all your Palo Alto Networks firewalls irrespective of their form factors or locations, in this forum.

Discussions

Start a conversation

Welcome to the Panorama Discussions!

To make this forum valuable and enjoyable for everyone, please review the following guidelines before participating: Rules and Best Practices Be Respectful: Treat fellow community members with professionalism and courtesy. Constructive discussions are encouraged; disrespectful or inflammatory comments are not. Stay On-Topic: This board is d...

JayGolf by • Community Team Member
  • 4910 Views
  • 0 replies
  • 0 Likes

Panorama Device Specific Templates Network Settings

In our Panorama exists a Standard Template. In the standard template I define ethernet1/5 with several sub interfaces. At one of our locations I need to add a sub interface for vlan 88. To tackle this, I have a device specific template that is in the template stack for this location. Within that device specific template, I added ethernet1/5....

AOneR by • L1 Bithead
  • 10591 Views
  • 4 replies
  • 0 Likes

Resolved! Panorama upgrade to 10.2.11 - Incomplete log entries

After upgrading Panorama to 10.2.11, we noticed various logs are either missing text , have a unknown severity (system logs), and show an inaccurate bit count.I've tried restarting the logd process and rebooted the box.Seems like a bug but I couldn't find anything in the known issues with 10.2.11.Any help is appreciated.

Robert2 by • L1 Bithead
  • 2117 Views
  • 2 replies
  • 0 Likes

Panorama support Azure site recovery service

Hi, I have deployed single Panorama in Primary region only to manage VM-series firewall deployed in Primary and secondary region. I have a requirement that Whenever my Primary region goes down Panorama moves from Primary region to secondary region and I could manage VM-series firewall in secondary region. Is Panorama supports Azure site rec...

Avinash by • L0 Member
  • 2220 Views
  • 1 replies
  • 0 Likes

Downgrading from 11.1.2-h3 to 10.2.0.h3

I know downgrading is not recommended but for a configuration management requirement I may have to downgrade from 11.1.2-h3 to 10.2.0-h3. On a test bench unit I upgraded it up to 11.1.2-h3, and following the downgrade procedure I downgraded to 10.2 directly and then re-apply the maintenance patch for 10.2.0-h3. I When I am looking at the boot p...

Query RE: Access Domains

Hi Team, I have a requirement as a user wanted to give full access to a Device Group A and Just a read only access only for monitor to a Device Group B. Will this be possible in Panorama using Access Domain or any other method ? Panorama

Edsnow by • L3 Networker
  • 1236 Views
  • 1 replies
  • 0 Likes

m500 to m700 migration

Has any attempted to migrate from an M500 Panorama to an M700? Palo support documents seem to indicate that there is a gap in support between the two hardware models. M500 final code release 10.1 and M700 initial code release 10.2. matrix link Palo Alto Networks Appliances

Panorama and managed devices secure comunication

Hello everyone, can someone help me figure out, how is secure communication built between managed firewalls and Panorama. The issue is that one of the firewalls lost connection, it was an ssl eror, I went by procedure recommended by panw to re-establish connection.But when consulting knowledgebase (https://knowledgebase.paloaltonetworks.com/KCSA...

Local Log collector Runtime Status showing "Disconnected"

Hi Mates, I want to know why Runtime status is disconnected. Error - Log collector XXXX failed to connect to XXXXX-inter-lc in the ring We are using Panorama as a "panorama" and "log-collectors" Setup is " Active/Passive. Issue : Managed Log collected Runtime status is showing disconnected and Configuration status is "in-sync" and Health Sta...

ike sa for gateway id not found

Hi Team, When we test the vpn and run the show vpn ike-sa ommand below, we see ID not found, is that mean there is config issue on palo side (other end is cisco) or is it becuase no traffic from peer. I am able to ping to peer ip but dont see any traffic comming from peer Also when i run tail follow yes mp-log ikemgr.log command, i dont see any...

shirishkulkarni_0-1726196733250.png

Content and anti virus version below panorama policy need a quick solution

Hello, Bootstrap is working on palo alto VMs installed in AWS. The FWs are pointing towards Panorama for everything (config, packages,etc) and do not have internet access. The issue we are running into is that our policy in Panorama for these Firewalls require them to be at a certain level for content and anti virus to be able to allo...

Pre-load software

Hello! I have a couple hundred firewalls that we centrally manage through Panorama. I am needing to update these firewalls to 10.1.1 outside of business hours, and that's going to take time. In my testing I had tried to send the software package to a lab firewall through Panorama, telling it NOT to install the software. However, when I went ...

ellisbw by • L0 Member
  • 3948 Views
  • 3 replies
  • 0 Likes

Resolved! . Failed to generate selective push configuration.

Hi all, I get the following message if i make any changes to device-group, "commit to panorama" works fine but when i push to devices it do not. . Failed to generate selective push configuration. Unable to retrieve last in-sync configuration for the device, either a push was never done or version is too old. Please try a full push. makin...

Resolved! We want to know which events should we be monitoring in SYSTEM events logs to know that the IPsec tunnel is down and back up again.

Hello, Would like to know which specific log events from the system logs for IPsec we should be monitoring to know that the IPsec tunnel has gone down and got back up. We don't have tunnel monitoring or path monitoring configured so this is the only way we can monitor the tunnel going up or down. Which logs in the SYSTEM logs can we monitor wh...

  • 853 Posts
  • 47 Subscriptions
Top Liked Authors
View All
LEGAL NOTICES
RESOURCES
Khoros awards 2022
Copyright 2007 - 2026 - Palo Alto Networks